648009
13
Zoom out
Zoom in
Previous page
1/17
Next page
24 25
Programming the Basic Settings
In general, all settings of your BionX electric propulsion system are pre-set. Basic display functions can
be set by entering the programming mode. Contact your dealer to customize the advanced functions of
your system.
Go to the Settings screen for the DS3 Display/RC3 Controller
Scroll through the cyclecomputer functions with the left or right toggle buttons until the display shows
“Settings”. Cycle the menus / values with or and confirm with the left toggle (Select) button. Move
back a menu with the right toggle (Scroll) button.
Turn on the programming mode for the G2 console
Simultaneously push and until the display shows “0000”. The first zero blinks. Change the value
of the selection with or and confirm with . Select the other digits in the same manner until the
desired program is displayed.
Note: For G1 programming, substitute (mode) and (crono) for (power) and (cycle)
respectively, and remain the same.
Code Description
2001 Select km/h or mph
2002 Regeneration/brake output (for reed switch) 0-40 (ideally 30-40)
2004 Clock adjust
2005 Tire circumference (millimeters)
2009 Flip Display: 0 = power left, 1 = power right (G2 only)
Code 2001 Code 2002 Code 2004
Select unit - km/h or mph. Select with
or , and confirm with .
Default value: 30. Change with
and
. Confirm with .
Select hour/minutes with
,
change value with
and .
Confirm with
.
Code 2005 Code 2009
Set tire size (in mm) - Select digits
one after another with
or , and
confirm with
.
Current setting of main functions is displayed. Flip = 0, assist toggle is
on
the right side of console; Flip = 1,
assist toggle is on the left side of console.
Confirm with
.
WARNING
Do not use other programming codes without consulting your authorized dealer.
If you type the wrong code, please push the key to exit programming mode.
Removing and Installing the Rear Wheel
We recommend the removal and installation of the rear wheel to be done by a qualified dealer.
Should you have to do this yourself, please follow the instructions below:
To remove the rear wheel
1
Make sure that the system is turned off via the console (no illustration)
2
Remove the neoprene covers (if applicable)
3
Disconnect the two cable connections that lead to the motor (COMMUNICATION
A
, before POWER
B
)
4
Disconnect the cable guide from the rear wheel brake (only on bicycles with rim brakes, not shown)
5
Loosen the axle nut on the rear wheel using a 15mm wrench
6
Slide the rear wheel downwards, out of the dropout
WARNING
Always turn off the propulsion system prior to connecting or disconnecting the motor
cables.
CAUTION
It is essential that the axle nuts are tightened to 40Nm (30lb-ft); this assures that the
propulsion system functions properly. Ensure the torque reaction collar is fully inserted
into the dropout. The notch on the non-drive side must also be facing in the direction of
6 o’clock (within 5° either way). If this notch placement is incorrect, please consult your
dealer.
If your bike is equipped with hydraulic disc brakes: Do not pull the brake lever with the
brake disc on the rear wheel removed from the caliper. Insertion of the wheel can be
difficult or impossible as the brake pads will prevent the brake disc from sliding in place.
15mm
15mm
40Nm
(30lb-ft)
15mm
15mm
40Nm
(30lb-ft)
40Nm
15mm
15mm
3
2
5
6
B
A
english
english
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BionX S-series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BionX S-series in the language / languages: English as an attachment in your email.

The manual is 4,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of BionX S-series

BionX S-series User Manual - German - 18 pages

BionX S-series User Manual - French - 17 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info