USING THE MEDICATION CUP
(SEE FIGS. 6, 7, 8 AND 9)
A medicated vapour can be distributed with the
“moist air” output.
To add medication to the vapour:
1. Switch humidifier off and allow removable
cover/outlet grill to cool down.
2. Lift the removable cover off (fig.6) to access
the medication cup.
3. Remove the medication cup (fig.7) from the
misting chamber.
4. Carefully add liquid medication; do not fill
cup more than half full.
5. Carefully place the medication cup into the
top of the misting chamber (figs.8 and 9).
6. Replace the removable cover back into the
unit.
7. Switch the unit on and press re-set bar if
power light does not illuminate.
8. After use, remove the cup from the unit and
clean any residue from the cup with warm water.
WARNING: DO NOT use any liquid
medication other than those specifically
recommended for use with a seam
vaporizer.
DO NOT pour medication directly into the
outlet grill openings nor add it to the water in
the tank.
AUTO SAFETY SHUT OFF
This humidifier is equipped with a
technologically advanced, safety system that
requires the user to reset the humidifier if there
is a potential overheat situation. When a
potential overheat temperature is reached, the
system will automatically shut the humidifier off.
It can only resume operation when the user
resets the unit.
RE-SET Bar This control, located on the
bottom right side, resets the humidifier after it
has shut down due to an empty water tank or
after it has been cleaned. Once the tank has
been refilled, allow one minute for the cavity to
fill then press the re-set bar. The re-set bar
should never be pressed when the unit is empty.
CLEANING AND MAINTENANCE
INSTRUCTION
The following maintenance procedures
must be routinely followed in order to
ensure proper, efficient operation of your
humidifier. The unit WILL FAIL if it is not
cleaned properly.
Regular cleaning prevents scale build-up on the
heating element and tray. It also prevents
microorganisms from growing on the tray and
tank. This ensures that maximum efficiency will
be achieved. We cannot over-emphasize how
essential proper cleaning is to the maintenance
and continued use of your unit and the
avoidance of algae or bacteria build-up.
Regular Maintenance
1. Be sure the unit is OFF and is disconnected
from the electrical outlet.
2. Remove the Water Tank.
3. Empty water and minerals from the Base.
4. Drain the water from the Tank into the sink
and rinse tank thoroughly. Leave to dry.
5. Wipe the Heating Element clean with a soft
cloth after it has had a chance to cool. The
Electronic Thermal Control Heating Element
is lined with a non stick coating that is
designed to provide the easiest cleaning and
prolong the operating efficiency of the
Humidifier. DO NOT use any metal or hard
objects to clean the Heating Element
6. Re-place the tank and lid onto the base.
7. Follow Operating Instructions.
NOTE:Never use detergents, gasoline,
kerosene, glass cleaner, furniture polish,
paint thinner or and other household solvent
to clean any part of the Humidifier.
De-scaling Maintenance
• Scale needs to be removed as it becomes
noticeable. We recommend using Bionaire™
Clean Away - Humidifier cleaning solution.
• Apply Solution with a plastic brush to scale
surfaces. Let it soak until residue is
softened. For cleaning the tank, mix 2
capsules of solution with 2 liters of water. Let
mixture stand for several minutes, swishing
every few minutes. Drain solution and
THOROUGHLY RINSE the tank.
If not available follow these
instructions:
1. Repeat steps 1-3 in the Maintenance section.
2. Clean the tray by partially filling the tray with
200ml of undiluted white vinegar. If the
element is heavily scaled, plug the humidifier
into an electrical socket and turn it ON for no
longer than 15 seconds. After this time turn
the humidifier OFF and unplug it from the
electrical outlet. Let solution stand 20
minutes, cleaning all interior surfaces with a
soft brush. Dampen a cloth with undiluted
white vinegar and wipe out entire tray to
remove scale.
3. Rinse with clean warm water to remove scale
and the white vinegar solution before
beginning to disinfect the tank.
4. Wipe the heating element clean with a soft
cloth after it has had a chance to cool.
STORAGE INSTRUCTIONS
If your humidifier will not be in use for two days
or more, or at the end of the season follow
these instructions.
20.This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless
they have been given supervision or
instruction concerning use of the appliance
by a person responsible for their safety.
Children should be supervised to ensure that
they do not play with the appliance.
21.If the supply cord is damaged, it must be
replaced by the manufacturer or its service
agent or a similarly qualified person.
22.Should the humidifier stop working, first
check the fuse in the plug (UK only) or
fuse/circuit breaker at the distribution board
is operating, before contacting the
manufacturer or service agent.
23.CAUTION: In order to avoid a hazard due
to inadvertent resetting of the thermal cutout,
this appliance must not be supplied through
an external switching device, such as a
timer, or connected to a circuit that is
regularly switched on and off by the utility.
IMPORTANT SAFEGUARDS
• Care should be taken when using the
appliance due to the emission of hot water
vapor.
• Unplug the appliance during filling and
cleaning.
• DO NOT Operate without water in the
tank.Turn the humidifier off when then tank
is empty or when the unit is not in use.
• DO NOT unplug the humidifier if your
hands are wet.
• Be sure to turn the unit off, unplug it and
allow the water inside the cavity to cool
before moving the unit or before cleaning it.
• Be sure to the tank filling cap is firmly
tightened and the tank O-ring is in place.
• DO NOT touch the heating element when
it is hot.
• ONLY place your CM1 on surfaces that are
water resistant.
• If you turn your CM1 unit off for extended
periods, empty the water tank.
• To avoid any possible spillage, be careful
when moving unit when it is full of water.
• If power supply cord or product becomes
damaged, in order to avoid potential
hazards, do not use the appliance but return
it to an authorized service facility for repair.
PRE-OPERATING INSTRUCTIONS
(SEE FIGS.1 - 2)
1. Be sure the Humidifier is switched to OFF
and the unit is disconnected from the
electrical outlet.
2. Select a location for your Humidifier, on a flat
surface, about 10cm (4") away from the wall.
DO NOT place the Humidifier on a finished
floor on or near furniture which can be
damaged by moisture or water. Place on a
moisture-resistant surface.
Filling the Water Tank
NOTE:This humidifier holds about 2.25L of
water in the tank and humidifier base. The
humidifier will produce up to 4.8L of moisture
over a 24-hour period, depending on the room
humidity and temperature.
1. If not already removed, remove the Tank
from the base of the Humidifier and take it to
the cold water tap. Turn the Tank upside
down and twist off the Tank Cap by turning
counter clockwise. Fill Tank with cool, fresh
tap water. DO NOT fill with warm water as
this may cause leaking. Replace the Cap on
the Tank FIRMLY but do not over tighten.
2. When full, carry Tank to the Humidifier and
place onto the Base. The water will
immediately begin to flow into Base.
3. Please wait for five minutes for water
chamber to fill with water from water tank.
4. Plug the power cord into a convenient 220/
240V AC electrical outlet.
OPERATING INSTRUCTIONS/FILLING
THE WATER TANK (SEE FIGS. 2, 3, 4 AND 5)
1. Place your CM1 humidifier in the desired
location. A hard level surface is necessary
for proper operation. Do not place your
humidifier on any surface that could be
damaged by water droplets.
2. Remove the top cover (fig.2) and then lift out
the water tank (fig.3). Carry water tank to a
water tap.
3. Turn the tank upright and remove the tank
cap by twisting it completely off (fig.4).
4. Fill the tank with cool tap water as shown in
(fig.5).
5. Replace the tank cap, making sure the O-
ring is in its correct position. Carry the full
tank and carefully replace it, cap down, into
the humidifier. Wait a few minutes for the
cavity to refill.
6. Turn your humidifier on by pressing on the
power switch. Press the re-set bar if the
power light does not illuminate. It may take
up to 5 minutes before full moist air output s
obtained.
7. When all the water in the tank has been
used, the unit will shut off.
NOTE: The tank may last up to 12 hours.
Do not add any additives to the water in the
tank or cavity.
WARNING: All cleaning agents must be
thoroughly rinsed away after use and
before the unit is returned to service.
3 4
