661008
6
Zoom out
Zoom in
Previous page
1/76
Next page
6
several times until the timer active icon
J
goes out.
You may also cancel the timer by turning the unit off
using the on/off button
F
.
CLEANING THE FILTERS
We recommend regular lter cleaning for optimal
performance.
Every few weeks, check the condition of both
lters.
After approximately 3 months of operation, the
lter service indicator icon
K
will appear on
the LCD display to alert you to clean the lters
before further use.
Depending on use, the lters should be
replaced after approximately 12 months.
Pre-lter
If you are replacing the lter, remove any packaging
from the new lter before tting.
1. Switch off and unplug your air purier from the
supply socket.
2. Referring to gure 2, press the rear grille latch
S
down and remove the rear grille
T
.
3. Remove the pre-lter
U
from the inside of the
rear grille.
4. Wash the pre-lter in warm soapy water.
5. Allow the lter to dry naturally on a at surface.
6. Once thoroughly dry, ret the pre-lter into the
rear grille then replace the rear grille onto your
air purier.
HEPA-type lter
If you are replacing the lter, remove any packaging
from the new lter before tting.
IMPORTANT: Do not use water, household puriers
or detergents to clean the lter. The lter may appear
discolored, even after vacuuming. This is normal and
does not affect performance in any way.
1. Switch off and unplug your air purier from the
supply socket.
2. Referring to gure 2, press the rear grille latch
S
down and remove the rear grille
T
.
3. Remove the HEPA-type lter
V
from your air
purier.
4. Using your vacuum cleaner, run the brush
attachment along both sides of the lter and
clean between the pleated layers.
5. After cleaning, ret the HEPA-type lter then the
rear grille.
Resetting the lter service indicator icon
1. With your air purier switched on, reset the lter
service indicator icon
K
by inserting a small
object (such as a pin or paper clip) into the
hole for the lter reset button
A
until the lter
service indicator icon goes out.
TROUBLESHOOTING
Problem Solution
The unit will not
operate
Make sure that the unit is
plugged in and switched
on
Decreased air ow Make sure that nothing is
blocking the air inlet or air
outlet.
Check the condition of the
lters and clean them if
necessary.
Make sure that the air
intake grill is at least 30 to
90 cm from the wall.
Filter appears dirty,
even after vacuum-
ing clean
This is normal and does
not affect performance in
any way. A new lter is not
necessary.
The lter service
indicator icon is still
on after cleaning
the lters.
See the Resetting the lter
service indicator icon section
in these instructions.
TECHNICAL SPECIFICATION
For all technical and regulatory information with
regards to your product specications under Eco-
Design Regulation No 206/2012, please contact our
consumer help line or visit www.bionaireuk.co.uk.
SPARE PARTS
HEPA-type lter 91382
Pre-lter 91383
UK - Filter Sales Order Line - 0870 759 9000
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bionaire BAP001X at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bionaire BAP001X in the language / languages: All languages as an attachment in your email.

The manual is 1,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info