661284
6
Zoom out
Zoom in
Previous page
1/8
Next page
-9- -10-
3. Lay the cuff on the arm as illustrated. Make
certain that the lower edge of the cuff lies
approximately 2 to 3 cm (
3
/
4~1
") above the
elbow and that the rubber tube leaves the cuff
on the inner side of the arm.
Important! The mark (about 3 cm long bar)
must lie exactly over the artery which runs
down the inner side of the arm.
4. Tighten the free end of the cuff and close the
cuff with the closer.
5. There must be no free space between the arm
and the cuff as this would influence the result.
Clothing must not restrict the arm. Any piece of
clothing which does (e.g. a pullover) must be
taken off.
6. Secure the cuff with the Velcro closer in such a
way that it lies comfortably and is not too tight.
Lay the arm on the table (palm upwards) so
that the cuff is at the same height as the heart.
Make sure that the tube is not kinked.
7. Remain seated quietly for two minutes before
you begin the measurement.
COMMENT:
If it is not possible to fit the cuff to the left arm, it can also be placed on the right arm.
However all measurements should be made using the same arm for better cross reference.
A FEW SUGGESTIONS BEFORE MEASUREMENT
1. Avoid eating, smoking, and exercising for at least 30 minutes before taking a measurement.
Also rest for at least 15 minutes before taking a reading.
2. Stress raises blood pressure. Avoid taking measurements during stressful
times.
3. You would better apply the cuff on your left upper arm.
4. Measurement should be taken in a quiet place and you should be relaxed, seated position.
Rest your left arm on a table.
5. Remain still and do not talk during the measurement.
6. Keep a record of your blood pressure and pulse for your doctor. Remember, a single
measurement does not provide an accurate indication of your true blood pressure. You
need to take and record several measurements over a period of time. Try to measure
your blood pressure at the same time each day for consistency. Blood pressure
measurements fluctuate considerably.
7. Wait 5-10 minutes between successive measurements.
Waiting allows the engorged blood
vessels to return to normal. You may require more rest time depending on your individual
physical conditions.
HOW TO MEASURE BLOOD PRESSURE
1. Set up the cuff to your upper arm as previous section of "How to use the upper arm cuff".
2. Press the "POWER" button, all icons appear two seconds on DISPLAY, then switch to
measurement mode,and display "0" or last measurement record.
3. Press "START" button to start measurement, the cuff in the strap will automatically inflate.
When the value on LCD increases to around 150-200 (mmHg), and start to release the
air, and
decrease pressure in the cuff automatically when it senses the heart beat, the
mark ( )
will flash on LCD.
2~3cm (
3
/
4~1
")
POWER
SYS
DIA
PULSE
-min
SYS
DIA
PULSE
-min
START
SYS
DIA
PULSE
-min
SYS
DIA
PULSE
-min
SYS
DIA
PULSE
-min
SYS
DIA
PULSE
-min
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bioland 2005 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bioland 2005 in the language / languages: English as an attachment in your email.

The manual is 4,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info