Manual Binatone Lifestyle 1900 (page 2 of 2) (English)

496735

Zoom out

Zoom in

1/2

6.3 Delete an entry in the Call List

1. Follow Steps 1 and 2 in Section 6.1.

2. Press <MENU> and <UP/DOWN> to select DELETE.

3. Press <OK> to confirm.

6.4 Delete

1. Follow Steps 1 and 2 in Section 6.1

2. Press <MENU> and <UP/DOWN> to select DELETE ALL.

3. Press <OK> to display CONFIRM?.

4. Press <OK> to confirm. All entries will be deleted and the display will show

EMPTY.

7 PHONE SETTINGS

Your phone comes with a selection of settings that you can change to

personalise your phone the way you like it to work.

7.1 Date and Time Settings

If you subscribe to Caller Display the time and date settings will be automatically

updated by the

The Caller Display service only sends the month and date, not the year, so you

may need to set the year.

7.1.1 Change the Date Format

1. Press <MENU> and <UP/DOWN> to select HS SETTINGS.

2. Press <OK> and <UP/DOWN> to select DATE & TIME.

3. Press <OK> and <UP/DOWN> to select DATE FORMAT.

4. Press <OK> and <UP/DOWN> to select your desired date format

(DD-MM-YYor MM-DD-YY

5. Press <OK> to confirm.

7.1.2 Change the Time Format

1. Press <MENU> and <UP/DOWN> to select HS SETTINGS.

2. Press <OK> and <UP/DOWN> to select DATE & TIME.

3. Press <OK> and <UP/DOWN> to select TIME FORMAT

4. Press <OK> and <UP/DOWN> to select your desired time format

5. Press <OK> to confirm.

7.1.3 Set the Time

1. Press <MENU> and <UP/DOWN> to select HS SETTINGS.

2. Press <OK> and <UP/DOWN> to select DATE & TIME.

3. Press <OK> and <UP/DOWN> to select SET TIME.

4. Press <OK> and then enter the time information in 24 hour format.

5. Press <OK> to confirm.

Note: If time has been set before, the current time will display, otherwise,

“HH:MM”

will display.

7.1.4 Set the Date

1. Press <MENU> and <UP/DOWN> to select HS SETTINGS.

2. Press <OK> and <UP/DOWN> to select DATE & TIME.

3. Press <OK> and <UP/DOWN> to select SET DATE.

4. Press <OK> and then enter the date information. The date entered will be in

5. Press <OK> to confirm.

Note: If date has been set before, the current date will display, otherwise,

the format you set in Section 7.1.1.

“DD-MM-YY ” will display.

7.2 Alarm Settings

You can set an alarm time on the handset. When an alarm is set, the <ALARM

Icon> is shown on the handset display.

<ALARM icon> and “ALARM ON” flash on the handset display, and the alarm

tone rings for 45 seconds. You can press any key to disable the alarm. If the

snooze function is activated, the alarm will sound again at the end of the snooze

period of seven minutes. You can also press and hold <TALK OFF> while the

Note:

a. A key press will still disable the alarm even if the handset keypad is locked

b. The alarm volume level is the same as the settings of the handset ringer

volume. If the handset ringer is set to VOLUME OFF, the alarm still sounds

at VOLUME 1

level.

when the alarm rings.

(12 HR or

24 HR).

c. During an external call or internal call, if an alarm is set and when the alarm

time is reached, the <ALARM icon> and “ALARM ON” will still flash. An

alarm tone will be emitted from the earpiece to alert the user the alarm time

is reached. Once the user presses any key or presses and holds

d. During paging or ringing, the alarm will not sound when the alarm time is

reached. However, if the snooze function is enabled and there is no paging

7.2.1 Turn on/off the Alarm

1. Press <MENU> and <UP/DOWN> to select HS SETTINGS.

2. Press <OK> and <UP/DOWN> to select ALARM.

4. Press <OK> to confirm.

Note: If ON is selected, you will be asked to set the alarm time.

7.2.2 Set the Alarm Time (If Alarm time is set to be ON)

1. Follow Steps 1 to 4 in Section 7.2.1.

2. Enter the alarm time in 24 hour format.

3. Press <OK> to display "SNOOZE".

4. Press <OK> and <UP/DOWN> to select snooze ON or OFF.

5. Press <OK> to confirm.

7.3 Handset Settings

7.3.1 Set the Ringer Melody for Internal Calls

1. Press <MENU> and <UP/DOWN> to select HS SETTINGS.

2. Press <OK> and <UP/DOWN> to select RING SETUP

3. Press <OK> and <UP/DOWN> to select INT RING.

4. Press <OK> and <UP/DOWN> to select the melody you want to hear for

Note: The respective melody will be played while browsing the ringtone list.

5. Press <OK> to confirm.

3. Press <OK> and <UP/DOWN> to select ON/OFF.

<TALK OFF> to disable the alarm, the display will revert to the call duration.

or ringing, the alarm will sound again at the end of the snoo .

internal calls.

7.3.2 Set the Ringer Melody for External Calls

1. Press <MENU> and <UP/DOWN> to select HS SETTINGS.

2. Press <OK> and <UP/DOWN> to select RING SETUP.

3. Press <OK> and <UP/DOWN> to select EXT RING.

4. Press <OK> and <UP/DOWN> to select melody you want to hear for external

Note: The respective melody will be played while browsing the ringtone list.

5. Press <OK> to confirm.

7.3.3 Set the Ringer Volume

1. Press <MENU> and <UP/DOWN> to select HS SETTINGS.

2. Press <OK> and <UP/DOWN> to select RING SETUP.

3. Press <OK> and <UP/DOWN> to select RING VOLUME.

4. Press <OK> and <UP/DOWN> to select the desired ringer volume (a total of

6 ringer volume levels including VOLUME OFF).

Note: The respective ringer volume will be played during your selection.

If VOLUME OFF is selected, the <Ringer Off> icon will be displayed.

5. Press <OK> to confirm.

7.3.4 Set Alert Tones

Three different alert tones are set on by default, but can be turned off, if desired.

Key Tone - a single beep is emitted when you press a key.

you need to charge the handset batteries.

1. Press <MENU> and <UP/DOWN> to select HS SETTINGS.

2. Press <OK> and <UP/DOWN> to select TONE SETUP.

3. Press <OK> and <UP/DOWN> to select KEY TONE / BATTERY TONE /

4. Press <OK> and <UP/DOWN> to turn on or off these tones.

5. Press <OK> to confirm.

Out of Range Tone - emitted while you are talking on the phone to alert you to

move loser to the base unit, before the call is lost.

Low Battery Tone - emitted while you are talking on the phone to alert you that

OUT OF RANGE.

7.3.5 Set the Handset Language

1. Press <MENU> and <UP/DOWN> to select HS SETTINGS.

2. Press <OK> and <UP/DOWN> to select LANGUAGE.

3. Press <OK> and <UP/DOWN> to select the desired language.

4. Press <OK> to confirm.

7.3.6 Ren

ame the Handset

1. Press <MENU> and <UP/DOWN> to select HS SETTINGS

2. Press <OK> and <UP/DOWN> to select RENAME HS.

3. Press <OK> and change the name of your handset, using <C/MUTE> to delete

4. Pres

s <OK> to confirm.

letters and the alphanumeric keys to enter up to 10 letters for the name.

7.3.7 Choose the Information to be Displayed in Idle

You can choose to display the time or handset name in your idle screen.

1. Press <MENU> and <UP/DOWN> to select HS SETTINGS.

2. Press <OK> and <UP/DOWN> to select HS DISPLAY.

3. Press <OK> and <UP/DOWN> to select HANDSET NAME or TIME.

4. Press <OK> to confirm.

7.3.8 Set the Auto Answer

If you turn on the Auto Answer, you can answer a call automatically by just lifting

1. Press <MENU> and <UP/DOWN> to select HS SETTINGS.

2. Press <OK> and <UP/DOWN> to select AUTO ANSWER.

3. Press <OK> and <UP/DOWN> to turn on or off the auto answer feature.

4. Press <OK> to confirm.

the handset off the base or charger, without having to press any key.

calls.

7.4 Base Settings

7.4.1 De-register a Handset

This operation should only be necessary if one of your handsets becomes faulty

or lost and needs to be replaced.

You will need to enter the 4-digit System PIN (Default PIN is 0000) in order to

Note: You cannot de-register the handset that you are currently using.

1. Press <MENU> and <UP/DOWN> to select BS SETTINGS .

2. Press <OK> and <UP/DOWN> to select DELETE HS.

3. Press <OK> and the display shows "PIN?".

the antenna icon flashing and "REGISTER" on the display.

de-register a handset from the base station.A de-registered handset will have

4. Enter the 4-digit system PIN.

5. Press <OK> and the first handset number is displayed.

6. Press <UP/DOWN> to scroll through the list of registered handsets and

7. Press <OK> to confirm, and the chosen handset will be de-registered.

select

the number of the handset you want to de-register.

network when you receive an incoming call.

7.4.2 Change the dial mode

1. Press <MENU> and <UP/DOWN> to select BS SETTINGS

2. Press <OK> and <UP/DOWN> to select DIAL MODE.

3. Press <OK> and <UP/DOWN> to select TONE or PULSE

(The current setting is indicated by an asterisk to the right).

4. Press <OK> to confirm.

You should normally leave the dialling mode at its default setting of TONE (also

called DTMF) unless the phone is connected to an old exchange that only

Note: If PULSE dialling is set, you can press the * key to switch to TONE dialling

recognises PULSE dialling.

for the rest of that call.

7.4.3 Change the Flash (Recall) Time

1. Press <MENU> and <UP/DOWN> to select BS SETTINGS.

2. Press <OK> and <UP/DOWN> to select FLASH TIME.

3. Press <OK> and <UP/DOWN> to select your desired flash time (SHORT,

4. Press <OK> to confirm.

You may need to change the recall (flash) time if your phone is connected to a

PBX. The recall time options are SHORT (the default value of 100ms), MEDIUM

( 0ms) or LONG (600ms).

MEDIUM,

7.4.4 Change the System PIN Code

A 4-digit system PIN code is used for changing the system settings of the base

station. It is used to protect your phone against unauthorised use. The default

system PIN code is 0000.

1. Press <MENU> and <UP/DOWN> to select BS SETTINGS.

2. Press <OK> and <UP/DOWN> to select CHANGE PIN.

3. Press <OK> and you are requested to enter the 4-digit system PIN.

4. Enter the old system PIN.

5. Press <OK> and enter the new system PIN.

6. Press <OK> and enter the new system PIN again.

Note: If the new PIN entered in Step 6 is not the same as the new system PIN

entered in Step 5, you must enter the new system PIN at step 5 again.

7. Press <OK> to confirm

7.5 Registration

already registered to your base, so you do not need to register them.

You can register additional handsets to have up to five handsets per base unit,

with each handset's number (1 to 5) shown on its display. (Note: each handset

1. Press and hold <PAGE> on the base station for more than five seconds, to

put the base station into registration mode. (Note: there is no feedback to

To register a new handset to your base:

2. Press <MENU> and <UP/DOWN> to select REGISTRATION.

3. Press <OK> and you are requested to enter the 4-digit system PIN.

4. Enter the 4-digit system PIN.

5. Press <OK> to confirm, and the display will show SEARCHING.

If the handset registration is successful, you will hear a confirmation tone and the

<antenna icon> will stop flashing. This may take a short while

The handset will automatically be allocated the next available handset number.

This handset number is shown in the handset display in standby mode. If the

handset registration is unsuccessful, the <antenna icon> will still flash and the

7.6 Reset Your Phone

You can reset your phone to the default settings . After a reset, all

your personal

settings, call list entries and redial list entries, will

1. Press <MENU> and <UP/DOWN> to select

DEFAULT.

2. Press <OK> and you are requested to enter the 4-digit system PIN.

3. Enter the 4-digit system PIN.

4. Press <OK> to display CONFIRM?

5. Press <OK> to confirm, and the phone will be reset to its default settings.

can only be registered to one base.)

minute, so the following handset sequence must be completed within this

unchanged.

DECLARATION OF CONFORMITY

UK (BTP) Ver 1, 200

Problem Causes Solutions

No dialling tone when

pressing <TALK ON>

a.The connection cord of

the base station is not

plugged in.

b.The adapter cord is not

plugged in correctly in

the base station.

c. Another handset is using

the base to make a call.

d. Wrong telephone line cord

a.Check the connections. Unplug

and plug back in the mains.

Check that the telephone cord

has been plugged into the base

station and the phone socket.

b.Check the base station plug and

the 230V plug (remove and plug-in).

c.Wait until the line is unoccupied.

d.Use the original telephone line

cord supplied

When connect to a PBX,

no and/or wrong connection

after dialling.

Dialling prefix is needed. Insert the dialling prefix

"SEARCHING" is displayed.

a. Base station out of

range.

b. Base station not

connected to mains.

Reduce the range.

Connect base station to

mains.

The call does not work.

Service not activated or

wrong operator or wrong

setting

Check your Subscription with

network or change the dial mode.

No display. Empty battery Recharge battery

key

8 TROUBLESHOOTING

Technical Support

If the fault persists...

Disconnect all other instruments connected to the same line as the

Disconnect the base unit from the telephone line and plug a different phone into

the master telephone socket.

Try making a call. If this works, the line is OK.

If the cal l does not work, and you are using a two-way socket adapter, remove

it and plug a telephone directly into the socket. If the call now works, the adapter

may be faulty.

Please contact the technical support of the network provider for further information.

This telephone is not equipped with a grounding function

used in PBX systems.

system and try to make a call .Lifestyle 1900

all Call list entries

alarm is sounding, to stop the alarm and turn off the snooze function.

ze period

LONG,

with the current setting indicated by and asterisk to the

right).

IMPORTANT: When you purchase a Lifestyle 190

Handset registration is only necessary when you buy extra handsets or if a

handset has become faulty.

remains

, and therefore some of

the functions may be limited when

We the manufacturer / Importer : Binatone Telecom Plc,1 Apsley Way London, NW2 7HF

Declare under our sole responsibility that the following product

Type of equipment:

Digital cordless telephone

Model Name:

Country of Origin:

China

Brand:

complies with the essential protection requirements of R&TTE Directive 1999/5/EC on

the approximation of the laws of the Member States relating to Radio Spectrum Matters,

the Council Directive 2004/108/EC on the approximation of the laws of the Member

Statesrelating to electromagnetic compatibility (EMC) and the European Community

Directive 2006/95/EC relating to Electrical Safety.

Assessment of compliance of the product with the requirements relating to the

essential requirements according to Article 3 R&TTE was based on Annex III of the

Directive 1999/5/EC and the following standard:

Manufacturer / Importer

(signature of authorized person)

Date

Signature

Binatone

The conformity to the requirements is validated by the

symbol.

NOTE: In compliance with Directive 2002/96/EC, when you purchase a product

that comes with the symbol shown on the right, you are required to dispose of

electrical and electronic equipment by separate waste collection and you

cannot dispose of the product as normal waste.

This equipment and all its components, subsystems and consumable materials

formed an

integral part of this product and when you decide to dispose

take them to a local recycling centre for

appropriate waste disposal, in compliance with the current regulations.

Details about the location of these centres can be obtained from

your local authority.

of them you have to

Notes for battery disposal

Your product contains batteries covered by the European Directive 2006/66/EC,

which cannot be disposed of with normal household waste.

Please the local rules on separate collection of batteries. The

correct disposal of batteries helps protect

the environment and prevent health

Lifestyle 1900 Series

30 Nov 2009

be aware of

hazards.

0 system, all handsets are

Radio Spectrum: EN 301406: V1.5.1 : 2003;

EMC: EN 301489-1: V1.8.1 : 2008;

EN 301489-6: V1.3.1 : 2008;

Electrical Safety: EN 60950-1: 2006.

When the alarm time is reached, the

display will return to "REGISTER", so you will need to repeat the registration

process.

know it is in registration mode.) It will stay in registration mode for about 1

time.

be deleted but your phonebook

The

purchase shown on your sales receipt. This guarantee

does not cover any

faults or defects caused by accidents,misuse, fair wear and tear, neglect,

faults on the telephone line, lightning, tampering with the equipment, or any

attempt at adjustment or repair other than through approved agents.

Please keep your sales (till) receipt this is your guarantee.

You should also keep the original packaging material.

In the unlikely event that you need to return your

While the unit is under Guarantee

1. Disconnect the base unit from the telephone line and the mains electricity

supply.

2. Pack up all parts of your Lifestyle 1900

3. Return the unit to the shop where you bought it, making sure you take your

sales receipt.

After the Guarantee has expired

Remember to include the mains adapter.

3. Call Helpline on 0845 345 9677 (for UK only) and ask for a quotation of the

repair charge and details of where to send your

for repair.

4. Make sure you include with your

5. Return your

If the unit is no longer under Guarantee, first follow steps 1 and 2 as for repair

under Guarantee. Then...

¾ Your name and address

¾ A cheque or postal order for the value of the repair

* This does not affect your statutory rights.

Department.

packaging.

Lifestyle 1900

GUARANTEE AND SERVICE

system is guaranteed for 12 months from the date of

system

to our Repair Centre while it is under guarantee, there may be handling charge.

system , using the original

system to the address given by the Service

system.

system

¾ A brief description of the fault

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Binatone Lifestyle 1900 in the language / languages: English as an attachment in your email.

The manual is 5,74 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Binatone Lifestyle 1900 Manual

Product: