496713
8
Zoom out
Zoom in
Previous page
1/11
Next page
04
Adjusting pedal resistance
You can adjust the pedal resistance on your Cyberbike™ using the knob loca-
ted at the base of the handlebar tube.
Rotate the knob in an anti-clockwise direction (towards the “-”) to decrease
resistance when pedalling.
Rotate the knob in a clockwise direction (towards the “+” ) to increase resis-
tance when pedalling.
• Pedal resistance can also
be adjusted when pedalling.
4.ADVANCED FUNCTIONS
4.a. Programming:
4.a.I. How to programme the buttons:
• Press the “PROGRAM” button. The LED underneath this button will come on.
Press the button or the direction that you wish to assign to another button
(e.g. the A button). The LED will start to ash steadily.
Press the button that you now wish to use (e.g. the B button). The LED will ash
rapidly for 2 seconds before going off.
Pressing the B button will now carry out the action previously assigned to the
A button.
You can then reprogram any other button or direction as you wish.
4.a.II. Cancelling programming:
• Press the “PROGRAM” button once. The LED will come on.
Press the programmed button (e.g. the B button). The LED will start to ash
steadily.
Press the programmed button again (or the «PROGRAM” button). The LED will
ash rapidly for 2 seconds before going off.
• The B button has now reverted to its original function.
4.a.III. Cancelling all programming:
Press the “START/PAUSE” and “PROGRAM» buttons at the same time and hold
down for 3 seconds. The LED located below the «PROGRAM” button will ash
for 3 seconds.
4.b. Calibrating the handlebar
Press the «PROGRAM” button + the “Y” button for 3 seconds. The LED located
below the “PROGRAM” button will ash.
• Centre the handlebar.
Press the “Y” button. The LED located below the “PROGRAM” button will now
ash more rapidly. The central position of the handlebar has now been set.
• Turn the handlebar to the left or right as far as it will go.
Press the «Y” button. The LED located below the “PROGRAM” button will ash
for 3 seconds before going off. The handlebar calibration process is now
complete.
Restoring the manufacturer’s calibration (default setting):
Press the “START/PAUSE” + “PROGRAM” buttons and hold down for 3 seconds.
The LED will ash for 3 seconds. The handlebar calibration will revert to its
default setting and any previous programming will be deleted.
4.c. Gamecube™ / Cyberbike™ modes
Use the Gamecube™ mode when you want to play with a Gamecube™/ Wii
game. When you want to play with your Cyberbike™ game use the Cyber-
bike™ mode.
CONFIGURATION:
The A / B / X / Y / L / R / Z buttons, the directional pad and analog joysticks
carry out the same actions as those on a traditional Gamecube™ controller.
Brake lever: the brake lever sends back the signal from the «B» button, and can
also be reprogrammed.
4.c.I. Gamecube™ mode
In Gamecube™ mode, FORWARD pedalling is the same as pressing the A but-
ton.
In Gamecube™ mode, REVERSE pedalling is the same as pressing the B button.
ENGLISH DEUTSCH ESPAÑOLFRANCAIS NEDERLANDS ITALIANO PORTUGUÊS
CYBERBIKEGAMECUBE
TMTM
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bigben PS3 Cyberbike at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bigben PS3 Cyberbike in the language / languages: English as an attachment in your email.

The manual is 1,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info