740637
17
Zoom out
Zoom in
Previous page
1/23
Next page
12 13
CHANGING LIGHT BULBS
Bielmeier extractor hoods are supplied with LED lights. Lightbulbs are wear parts and can be ordered from the
manufacturer on demand as spare parts.
However, the use of LEDs as workstation lights makes the need to replace defective lights highly unlikely. Service
life, reliability, and energy efficiency are significantly above those of conventional lightbulbs, such as halogen,
fluorescent tubes, etc. However, proceed as follows if the lights nevertheless fail:
Changing LED lightbulb
Pull power plug and/or disable circuit breaker!
In order to reduce dirt buildup in the hood interior, the LED spotlights for the workstation lighting are mounted
flush with the hood body.
1. Open the cover plate and remove the grease filter.
2. Now push the complete LED spotlight from the interior to the outside.
3. Disconnect the connector for the defective spotlight.
4. Connect the new spotlight with the connector.
5. Then gently push the spotlight back into the housing.
NOTE: If the lights fail to work, check whether the lights are seated properly. Defective lights should be replaced
promptly to avoid overloading the remaining lights.
Contact customer service if the lights do not work after the lightbulbs were replaced.
STARTUP – OPERATION
Operator panel - electronic control: BHG52, BHG53, BHG59, BHG58
Lighting Output Output Display Output Dwell Timer Operator
Controls increase decrease remotecontrol
on / off
The operator panel is located on the front of the equipment. It has a user-friendly design and is easy to operate.
Operator panel - electronic control: BHG41
Operator controls Lighting Output
Remote control on / off
Dwell timer Output display Output Blower
decrease on / off
Operator panel - electronic control: BHG39, BHG93
Operator control Blower on/off Dwell timer
Remote control
Output display Output Output Lights
on/off
Operator control / remote control
This unit can also be conveniently controlled with the included IR remote control:
Electronic control
Lights on/off
The lights are switched on or off by touching this control surface.
When is touched (increase output)
a „5 or F5“ is displayed in the output display. This means: the highest output level is automatically selected when
this control surface is pressed. The output level is continuously incremented up to the highest output level when
the control surface is depressed continuously.
GB
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bielmeier BHG39 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bielmeier BHG39 in the language / languages: English, German as an attachment in your email.

The manual is 2,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info