528786
33
Zoom out
Zoom in
Previous page
1/71
Next page
33
Diese Sicherungsvorrichtung wird
ausgelöst, wenn das Gerät einer
ungewöhnlichen Belastung oder einer
Überhitzung ausgesetzt ist.
Wenn ein solcher Fall auftritt,
1.- Stellen Sie den Schalter (L) am
Gehäuse auf Position “0 (OFF) Fig.B.
2.- Betätigen Sie den Schalter (C), um
den Kreislauf zuckzusetzen.
3.- Stellen Sie dann den genannten
Schalter auf Position “I (ON) und das
Gerät kann wieder genutzt werden.
Sollte die Schutzvorrichtung wiederholt
auslösen, kann dies folgende Ursachen
haben:
- ungewöhnliche Betriebsbedingungen,
- zu geringe Schmierung des
Laufbands,
- es wurden Schmiermittel mit
Lösemitteln benutzt,
- das Band ist zu stark gespannt.
Schließen Sie das Gerät an einen
GEERDETEN Stecker. Schalten Sie
den Schalter (L) auf Position [1].
Fig.B
MONTAGEHINWEISE.-
Nehmen Sie das Gerät aus der Kiste
und stellen Sie es auf den Boden
Fig.0.
Es ist ratsam, dass die Montage
von zwei Personen vorgenommen
wird.
Prüfen Sie, ob alle Teile vorhanden
sind:
(2) Hauptrahmen; (4L) Vertikale
Haltestange (links); (4R) Vertikale
Haltestange (rechts); (5)
Monitorhalterung; (19) Monitor; (13)
Gekrümmte Inbusschraube M-8x25;
(30) Gekrümmte Inbusschraube M-
6x15; (39) Sicherheits-schlüssel;
Inbusschlüssel 5mm; (305)
Inbusschlüssel 6mm; (100)
Fläschchen mit Schmiermittel.
Folgen Sie bitte den angegebenen
Montageschritten.
1 Führen Sie (4R) zunächst die
Endklemmen (17) (18) Fig.1 heraus.
Setzen Sie die Haltestange dann auf
die untere rechte Halterung des
Hauptrahmens und schrauben Sie sie
mit den Schrauben (13).
2 Setzen Sie dann die Haltestange
(4L) in die untere linke Halterung des
Hauptrahmens und schrauben Sie sie
mit den Schrauben (13) fest.
3 Für diesen Schritt benötigt man
mindestens zwei Personen. Bei der
Montage der Haltestangen muss eine
Person die Stange festhalten,
während die andere die Schrauben
(13) festzieht. Auf diese Weise können
mögliche Unfälle vermieden werden.
4. ANBRINGEN DES
MONITORROHR.-
Fig.3 Verbinden Sie dann die
Klemmen (33) aus dem Monitorrohr
mit der Klemme (17) aus dem
Handlauf. Führen Sie die Klemmen in
die Monitorrohre (A) ein. Schieben Sie
die Kabel in Pfeilrichtung in die
Handlaufrohre. Achten Sie dabei
darauf, dass die Kabel nicht
eingeklemmt werden.
Ziehen Sie anschließend die
Schrauben (13) fest.
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BH Fitness G6327 V1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BH Fitness G6327 V1 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info