470418
35
Zoom out
Zoom in
Previous page
1/44
Next page
35
10. First steps with SensEpil™ by beurer
10.1. SensEpil™ by beurer Setup
1. Remove SensEpil™ by beurer BASE UNIT, APPLICATOR and other components from box.
2. Verify that the
DISPOSABLE LAMP CARTRIDGE is inserted correctly into the APPLICATOR.
3. Plug the power cord into the SensEpil™ by beurer
BASE UNIT socket.
4. Plug the other end of the power cord into an electrical outlet. The
STAND BY INDICATOR LIGHT
will turn on.
Your SensEpil™ by beurer is now ready to start.
10. Remove the APPLICATOR TIP from the treated area of skin.
11. Move the
APPLICATOR TIP to another area of skin.
Use the pressure marks the device just made on your skin to guide you for proper positioning of the next pulse, avoiding both gaps
and overlaps between pulses (See “Covering skin areas” frame).
If you see no light pulse and the SKIN TONE WARNING INDICATOR LIGHT blink for 3 seconds, your skin tone, measured by
the
SKIN COLOR SENSOR, is too dark for safe application. Try using the device on a different body part or contact the
SensEpil™ by beurer support (See: “The Skin Color Sensor” frame).
10.2. Treating with SensEpil™ by beurer for the fi rst time
The skin should be shaved, clean, dry and free of any powders, antiperspirants or deodorants.
5. Press the
POWER ON/STANDBY SWITCH. The POWER ON INDICATOR LIGHT will turn on and a fan sound (similar to the sound of a
hairdryer) will start.
6. Approximately 3.5 seconds after pressing the
POWER ON/STANDBY SWITCH, the READY INDICATOR LIGHT will turn on and the device will
beep. The device sets itself to deliver the lowest energy level pulses. The device is then ready for you to trigger the fi rst pulse.
7. If the energy level should be higher than the lowest, press the ENERGY LEVEL SETTING BUTTONS using the “-” or “+” to respectively
decrease or increase the energy level, until the desired energy level is set.
ENERGY LEVEL INDICATOR LIGHTS will coincide with the
energy level setting. (See “Energy Level” frame).
8. Apply the
APPLICATOR rmly to the skin, making sure the skin is spread evenly and smoothly. Make sure the APPLICATOR TIP is in
full contact with the skin.
9. Press the PULSE BUTTON. The device will fi rst determine the color of your skin.
If the color of the skin is light enough for safe application, the device will fl ash a pulse of light onto your skin. You will see a bright
ash of light and simultaneously hear a subtle pop sound, which is a normal noise for the device. You may feel a mild sensation
of warmth and tingling.
SensEpil™ by beurer will immediately recharge for the next pulse. After 3.5 seconds the
READY INDICATOR LIGHT will turn on again
and the device will beep.
12. Repeat the process starting again with Step 5.
Warning: Do not treat the same area of skin more than once per hair removal session! Treating the same area of skin
more than once per session increases the likelihood of adverse effects.
35


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Beurer HL 100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Beurer HL 100 in the language / languages: English, German as an attachment in your email.

The manual is 2,51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info