470146
15
Zoom out
Zoom in
Previous page
1/18
Next page
14 15
Apply the thermometer to the left or right temple and press the "SCAN" button. Move the thermo-
meter to and over the temple. During the measurement you can hear short beeps signalling that the
thermometer has found a new maximum temperature. The end of the measuring time is signalled with
a long beep. Release the “SCAN” button. You can now read off the temperature measured. The LED is
also illuminated according to the test result: a green LED indicates that body temperature is within the
normal range, but a red LED lights up with measured values over 37.5 °C, i.e. it is a fever alarm. The
measurement normally takes from 5 to 8 seconds, but can take up to 30 seconds.
The thermometer signals with two short beeps and a no longer flashing forehead symbol that the thermometer is ready for
a new measurement.
6.2 Saving the temperatures measured
The temperature last measured, i.e. only the last temperature of a series measured, is saved automatically as soon as the
thermometer is switched off. There are 9 memory locations available for this.
You can call up the last temperature measured with the “ ” button. The date and time are also shown. The LED does not
support any requests for stored measured values. If you continue to hold down the “ ” , you will enter a special measu-
ring mode, in which the thermometer will not make a correct measurement. In this event, allow the thermometer to switch
off automatically after about 1 minute and then switch it on again.
6.3 Surface temperatures
When you want to measure surface temperatures with this infrared thermometer, you must change to the “SCAN” mode.
With the thermometer switched on (standard forehead thermometer mode) keep the “ ” button depressed and at the
same time press the “SCAN” button. This mode is indicated with the symbol. If you keep the “SCAN” button de-
pressed, the surface temperature measured is continuously displayed. You can apply the sensor tip directly to the surface
to be measured or measure at close range (do not immerse in liquids).
Note that the temperature displayed is the surface temperature measured but not adjusted. It cannot be compared with
the forehead temperature.
6.4 Ambient temperature
After the measurement, the thermometer automatically switches to standby mode after about 1 minute, but only if the
time has been set. This mode is identified by the symbol and the ambient temperature is shown continuously.
If you want to use the thermometer to measure the ambient temperature, it should be positioned so that the measurement
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Beurer FT 60 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Beurer FT 60 in the language / languages: English, German, French, Italian, Polish, Turkish, Spanish as an attachment in your email.

The manual is 0,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Beurer FT 60

Beurer FT 60 User Manual - Dutch - 102 pages

Beurer FT 60 User Manual - Dutch - 12 pages

Beurer FT 60 User Manual - Danish, Portuguese, Swedish, Norwegian, Finnish - 102 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info