Manual Bestway 60025 Helsinki (page 12 of 252) (English, German, Dutch, French, Italian, Polish, Portuguese, Swedish, Spanish, Finnish)

809083

Zoom out

Zoom in

1/252

PRE-SETUP

CHECK LIST

To check the parts printed on the package, verify that the

equipment components represent the model that you had

intended to purchase. In case of any damaged or missing

parts at the time of purchase, visit our website

bestwaycorp.com/support.

CHOOSE THE CORRECT LOCATION

Indoor and outdoor & above ground & portable wiring &

portable spa.

Only For Spas Equipped With Wi-Fi:

To choose the correct location for the spa equipped with Wi-Fi,

read the Spa Wi-Fi instruction leaflet included in the package

and the following instructions.

For All Spas:

The surface chosen to install the pool must respect the

following technical characteristics.

• Because of the combined weight of the water inside the spa

and the users, it is extremely important that the surface

chosen to install the spa is capable of uniformly supporting

the total weight for the entire time the spa is installed.

• An adequate drainage system has to be provided to deal with

overflow water for both indoor and outdoor installations.

During filling, draining or when in use, water may flow out of

the spa.

• The surface must be flat and smooth. If the surface is

inclined or uneven, it can create an unbalanced loading on

the structure of the spa. This situation can damage the

welding point.

• The selected surface must be clear of any type of object.

Due to the weight of the water, any object under the spa

could damage or perforate the bottom of the spa.

• The selected location must not have overhead power lines or

trees. Be sure the location does not contain underground

utility pipes, lines or cables of any kind.

• The selected position must be far from the house entrance.

Do not position any equipment or other furniture around the

spa. The water that comes out of the spa during the use or

due to a faulty product can damage the furniture inside the

house or surrounding the pool.

• Do not to install the spa on carpet or other floor materials

(e.g. untreated cork, timber or other porous materials) that

promote or harbor moisture and bacteria, or that could be

affected by water treatment chemicals used in the spa.

• Consult your local government authority for installation

regulations.

Suggested set-up surfaces: grass, ground, concrete, and all

other surfaces that respect the above set-up conditions.

Not suggested surfaces: mud, sand, gravel, deck, balcony,

driveway, platform, soft/loose soil or other surface that does

not meet the above set-up conditions.

Indoor Installation:

Be aware of special requirements if you install the spa

indoors.

• Humidity is a natural side effect with Lay-Z-Spa installation.

Determine the effects of airborne moisture on exposed wood,

paper, etc. in the proposed location. To minimize these

effects, it is strongly recommended to provide plenty of

ventilation to the selected area. Consult an expert to

determine if more ventilation is needed.

• Keep suitable air treatment in the indoor location (ventilation

and dehumidification) regularly to preserve the bathers’

safety and comfort.

• Empty the spa before removing it from the indoor location or

building.

Outdoor Installation:

• The selected surface must be clear of aggressive plants and

weed species. Those types of strong vegetation could grow

through the liner and create water or air leakage. The grass

or other vegetation that may cause odor or slime to develop

have to be eliminated from the set-up location.

• Do not leave the spa's surface exposed to direct sunlight for

long periods of time. We recommend protecting the spa from

direct sun light exposure by a cover when not in use.

Follow the important instructions above to choose the correct

surface and location to set up your spa. Damaged parts of

the spa, due to the fact that the set-up surface and location

does not match the instructions, will not be considered as

manufacture defect and will avoid the warranty and any

service claims. It is the responsibility of the owner to ensure

the site meets the requirements at all times.

• Consult your local professional installers for environmental

conditions, such as ground water and risk of frost.

• Recommended to protecting the spa from direct sunlight

exposure by a cover when not in use.

SPA HEATER EQUIPOTENTIAL BONDING TERMINAL

• It is recommended to arrange for a qualified electrician to

connect the spa pump to an equipotential bonding terminal

using a minimum 2.5mm

solid copper conductor.

HEATING RESET

• When using the Lay-Z-Spa for first time,

or after a long period of inactivity, be

sure to press the reset button on the

pump using a small and thin object.

• If the temperature on the control panel

(or the water temperature) has not

changed for 4-5 hours after activation of the heating system,

use a thin object to press the RESET BUTTON, and restart

the heating system.

• If the Lay-Z-Spa is under direct sunlight and the outside

temperature is above 35ºC there is a risk that the heating

system will not operate, and the display will show the alarm

code E08. Under these conditions, please wait until a cooler

time of day before pressing the RESET BUTTON with a thin

object and restarting the heating system. If the spa remains

in the same position, the alarm E08 can appear again. In that

case follow the same procedures.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bestway 60025 Helsinki in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 4.01 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bestway 60025 Helsinki

Bestway 60025 Helsinki User Manual - English - 36 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bestway 60025 Helsinki Manual

Product: