The WATER HEATER rate may change in the conditions below:
• When the outdoor temperature is below 15°C (59°F).
• If the cover is not in position. Always keep the spa cover on when the spa is not in use; it avoids dust contaminating the water and it minimizes heat
loss.
• The water temperature shown on the display may not be correct, if the filtration system is not activated. To read the correct water temperature on the
display, run the filtration system for at least a minute.
• The water temperature as tested by an external thermometer may vary from the temperature as displayed on the spa panel by as much as
approximately 2°C (35.6°F).
HEATING TIME
• To reach 40°C (104°F), the heating duration required is based on the starting water temperature and ambient temperature, the data below is purely for
reference. To display the current water temperature, run the filter system for at least a minute.
• Be sure to cover the spa with the spa cover whenever the heating function is activated. Leaving the spa uncovered will increase the heating duration
required. When the spa is assembled with water, do not switch off the spa heater if the temperature is lower than 6ºC (42.8°F).
16
WATER FILTER BUTTON: The button turns the filter pump on and off. The button turns to red when activated.
TEMPERATURE ADJUSTMENT BUTTONS: Pressing the or button, the display starts to flash showing the set temperature for
3 seconds, after that it will show again to the real water temperature. When it is flashing you can adjust the temperature using the or
button.
The default temperature is 35°C (95°F).
Temperature adjustment ranges from 20°C (68°F) to 40°C (104°F).
ON/OFF BUTTON: After activating the PRCD, press and hold the button for 2 seconds. The button turns to green and the control
panel is activated. Press and hold button for 2 seconds to turn off all currently activated functions.
CELSIUS/FAHRENHEIT TOGGLE: The temperature can be displayed in either Fahrenheit or Celsius.
FOR SPA EQUIPPED WITH Wi-Fi ONLY
Wi-Fi ACTIVATION: For the Wi-Fi operation instruction, read the spa Wi-Fi instruction leaflet included in the package.
WINTER USE INSTRUCTIONS
SPA HEATER SPECIFICATION
Ambient Temperature
10ºC (50ºF)
15ºC (59ºF)
20ºC (68ºF)
25ºC (77ºF)
30ºC (86ºF)
Water Temperature
10ºC (50ºF)
15ºC (59ºF)
20ºC (68ºF)
25ºC (77ºF)
30ºC (86ºF)
Set Temperature
40ºC (104ºF)
40ºC (104ºF)
40ºC (104ºF)
40ºC (104ºF)
40ºC (104ºF)
Heating Duration
16-24h
12-20h
10-18h
8-12h
5-8h
Power RateMassage Tube PowerHeat Element PowerWater Pump Power
2,000W at 20ºC50W
220-240V AC, 50/60Hz,
Single Phase 2,050W at 20ºC800W
It is important to follow these suggestions if you are setting up the spa during the winter period. This will prevent any damage to the spa
heater and material of the liner, extending the life of your product drastically.
• If the outdoor temperature is below 10°C (50°F), to avoid any damage to spa liner, keep the package indoors where the temperature is above
15°C (59°F). This will make the spa liner more flexible and easier to set up.
• Open the package and inflate the spa liner using the spa heater in a room where the temperature is above 15°C (59°F).
• Position the spa liner outdoors in the desired position, then connect the spa heater and fill with water. The water temperature used to fill the spa must be
above 6°C (42.8°F), otherwise when you begin to operate with the spa heater, the E03 alarm will appear.
• You can keep the spa on during winter when the temperature is lower than 6°C (42.8°F). The Freeze Shield™ system automatically keeps the water
temperature between 6°C (42.8°F) and 10°C (50°F), and it will prevent the water from freezing.
• If the water temperature is below 6°C (42.8°F), the spa heater must always be on. In this mode, the Freeze Shield™ system can keep the internal
temperature between 6°C (42.8°F) and 10°C (50°F) to prevent damage, such as water freezing in the pipes or the circulation system.
• If any alarms appear on the display, the Freeze Shield™ system isn’t working. Be sure to check the status of your spa if the outdoor temperature is
below 6°C (42.8°F). In case of a long-term absence from home when there is a risk of temperatures falling below 6°C (42.8°F), we strongly suggest
disassembling the spa and storing it following the storage procedure.
• Any damage as a result of using the spa in these conditions is the responsibility of the customer. Do not use the spa when the ambient temperature
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Bestway 60013 Paris at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Bestway 60013 Paris in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Swedish, Spanish, Finnish as an attachment in your email.
The manual is 4.01 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
