686843

Bestway 58340 Flowclear AquaScan Electric Pool Vacuum Manual

2
Zoom out
Zoom in
Previous page
1/68
Next page
2
NO. Description
Battery cover
Battery holder
Handle
On “I”/Off “O” button
Adjustable pole
Pole lock
Impeller
Water vent
Suction head
Brush
1
2
3
4
5
6
7
8
9
10
Note: Drawings for illustrations purpose only. May not
reflect the actual product. Not to scale.
Set Up of Vacuum Product
Brush Assembly
Align the curvature of brush with the suction head and
insert the brush into it securely (Fig.1).
Suction Head Assembly
Carefully discard the cardboard wrap around the impeller.
Don’t try to pull the wrap away directly, but cut and unroll it.
Any damage on impeller may cause it to function improperly.
Screw the suction head securely to the threaded connector as
shown (Fig.2).
Battery Assembly
Unscrew the battery cover and take out
the battery holder.
Place 8 AA batteries into the battery
holder according to the polarity marked
on it.
Align the rib and slide the battery holder
into the compartment with the word “TOP”
facing outwards as shown (Fig.3).
Screw the battery cover on tight and
make sure it is secure (avoid stripping the
screw).
CAUTION: Do not press the button to turn
the product on until the cleaner is
submerged in the water and water level is
above the water vent.
Fig.5
Fig.4Fig.4
Fig.6
Fig.6
Cleaning Your Pool or Spa
Place the product into water and make sure water level is above
the water vent. You can adjust the product length by unscrewing
the pole lock to release the top pole and then extend it to the
desired length according to your pool or spa size. Secure by
tightening the pole lock. Press the “I” marking on the button to start
vacuuming.
CAUTION: Never submerge the handle in
water. During operation, avoid water contact
with the handle and button. Never use the
product without filter basket in place. This can
cause permanent damage to the product
impeller and motor.
Cleaning the Pre-filter Bag
WARNING! Turn off the product before
proceeding following steps.
NOTE: Water will be stored inside the
transparent tube and the pole after use. To
remove the water, lift the product from the
pool or spa with the nozzle facing down to
allow the water to drain out.
1. Pull the edge (on back side) of cover to lift its tab (inside) from
the notch on the body, and then pull it down to completely
release the cover (Fig.4).
2. Pull out the pre-filter bag. Empty this bag by removing the
leaves and other debris, and then rinse it. Rinse the cover and
make sure its suction hole is not clogged (Fig.5).
3. Reverse the previous steps to assemble the pre-filter bag back
to the cover and then the cover to the body. Make sure the tabs
on cover inside (2 sides) are secured in the notch of the body
before next operation (Fig.6).
Maintenance and Storage
WARNING! Turn off the product before
any maintenance.
• Always check if the pre-filter bag is full
of debris. Clean if necessary.
• Always check if the suction nozzle is
clogged. Turn off the power
and clean it out.
•
If the impeller becomes clogged, be sure
the product is in the off position.
• Remove batteries from compartment.
Remove pre-filter bag and check for
holes or damage (replace if necessary).
• Flush water vent “8” with water.
Remove any visible debris. Replace
pre-filter bag, fittings, batteries and
battery cover. Place water vent under
water and turn product switch on. If still
cannot remove the debris by this way,
unscrew the impeller chamber and
remove the debris carefully, not to
damage the impeller.
NOTE:
Never pull and torque the impeller.
• After use, always drain water from the
unit by removing the nozzle, hold it
vertically, and dry it before storing.
• Do not leave the unit in the pool or spa
when not in use. Do not store under
direct sunlight.
• Do not store the unit outdoors or in a
location where the temperature falls
below freezing.
• Remove the batteries and the case
when the unit is not to be used for a
period.
• Always keep the battery chamber and
compartment dry.
Fig.3
Fig.2
Fig.1
2 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bestway 58340 Flowclear AquaScan Electric Pool Vacuum at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bestway 58340 Flowclear AquaScan Electric Pool Vacuum in the language / languages: All languages as an attachment in your email.

The manual is 2,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info