652129
3
Zoom out
Zoom in
Previous page
1/82
Next page
10 11
4. When mounting in the front seat of the vehicle, adjust the back rest into an
upright position.
5. Positioned in the front seat of the vehicle, you should position the seat against
the dashboard.
6. If it’s not possible to position the seat against the dashboard, position the seat
as far as possible from the dashboard.
7. Find the ISOfix anchorage points in the vehicle. (4)
8. If your vehicle is not equipped with ISOfix insertion clips insert these to make
installation easier. (5)
9. ISOfix insertion clips are underneath the base.
10. Install the front brace by sliding the two pins into the oval tube under the
front side of the seat. Move the front brace inwards with the ratchet. The
ratchet is used to adjust the front brace in both directions. Slide the switch on
the ratchet up or down to change direction. (6)
11. Pull both ISOfix connectors as far out as possible, by pushing the grey buttons
on top of the base. (7)
12. Remove the caps from the ISOfix connectors by pressing down the ISOfix
release buttons. (8)
13. Click the installation clips on the ISOfix connectors. (9)
14. Fold down the floor support before you install the seat in your vehicle. (10)
15. Place the seat sideways into the car with the front brace towards you.
16. Turn the seat into the right position (with the front brace against the
back rest).
17. Click the ISOfix connectors in the ISOfix anchorage of the vehicle. (11)
18. Remove the installation clips.
19. Make sure that all indicators on both sides are green. (12)
20. Push the seat towards the backrest of vehicle seat till the frontbrace touches
the backrest; the isofix arms slide in and will click into a new position. (13)
21. Move the front brace outwards with the ratchet. Continue tightening until the
brace is pressed well into the back rest of the vehicle seat. (14)
22. Remove the cap around the floor support. An alarm sound will start and stop
when the seat is installed correctly with the floor support in contact with the
floor of the vehicle seat. (15)
23. Adjust the floor support so it is in contact with the floor of the vehicle. (16)
24. The height indicator of the floor support shows green when the floor support
is in contact with the floor. (17)
25. The alarm sound stops when the floor support shows green and is in contact
with the floor.
26. Positioned in the back seat of the vehicle, you should, if possible, push the
front seat of the vehicle backwards, so that it is in contact with the child seat.
If it is not possible to obtain contact with the child seat, push the back rest of
the front seat of the vehicle forward as far as possible.
27. When the child has a stature height of 87 cm. or more, use the seat in the
upright position.
28. When you want to enlarge the available space for your child, keep the isofix
arms totally slided out without pushing the seat towards the backrest, and
tension the frontbrace outwards with the rachet.
29. Make sure the floor support is fully pushed down, in contact with the floor of
the vehicle, and locked.
30. Make sure that all indicators on both sides are green.
31. The seat is delivered with removable SIP+ (side impact protection +). This extra
side impact protection should be used on the doorside of the vehicle. It can be
connected by slotting between the seatshell and the fabric. The seat already
oers high level integrated side impact protection. This extra side impact
protection improves the protection in the side impact still further. (Not on all
models) (18) Do not use the SIP+ on the seat when the space between seat
and door of the vehicle is too small, which might lead to a situation were the
seat is not positioned correctly on the vehicle seat.
Removing the seat
1. If the seat is installed in the back seat of the vehicle, push the front seat of the
vehicle forward as much as possible.
2. Move the front brace inwards with the ratchet. (19)
3. Release the ISOfix connectors by pressing the release mechanism on the ISOfix
connectors. (20)
4. Push the switch on each side and push the ISOfix connectors into the base. (21)
5. Pull the seat back towards the front. Turn the seat so you can easily remove
the seat.
6. Remove the insertion clips from the vehicle. Place them under the base of the
child seat.
7. To remove the front brace from the metal tube, move the front brace outwards
with the rachet, until the lock button of the front brace appears. Push the lock
button down with a small screw driver, while pulling the front brace out. (22)
Positioning of the child
1. Check that the shoulder strap slots are level with your child’s shoulders. (23)
2. The height of the shoulder straps and the head rest can be adjusted by pulling
the release handle upwards at the back of the head rest and pulling the head
rest up or down while keeping the head rest upright. (24)
3. Pull the shoulder straps up while pressing the button of the central
adjuster. (25)
4. Open the harness buckle. (26)
5. Position the shoulder straps over the orange marking at sides of the seat to
keep the harness open while you position the child. (27)
6. When the child is positioned, place the shoulder straps over the child’s
shoulders and close the buckle: CLICK! (28)
7. Pull the harness strap through the central adjuster in the direction of the
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BeSafe iZi Kid X2 i-Size 2015 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BeSafe iZi Kid X2 i-Size 2015 in the language / languages: All languages as an attachment in your email.

The manual is 2,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info