605228
7
Zoom out
Zoom in
Previous page
1/40
Next page
7
ATTENTION: The appliance conforms with the regulations of directives
90/396EEC (Gas Directive) regarding gas appliances for domestic use and the
like, 73/23 (Low Voltage Directive) regarding electrical safety and 2004/108/CE,
(EMC Directive) regarding electromagnetic compatibility.
Ensure that the electricity supply is switched off before making the connection. This
appliance must be earthed.
Connection to the electricity supply must be made through the flex cable that is
already attached to the rear of the cooker. The end of the cable is tucked into the
cooker storage area.
Connection to the supply must be made through fixed wiring. It cannot be connected
to a normal domestic power socket. A double pole switched cooker box should be
used with contact separation of at least 3mm.
Turn on each hob zone to check that all elements are functioning correctly. Remove
all packaging and combustible items from the oven. Turn on the oven selector switch
and thermostat knob to check that the oven is functional on all modes.
Adaptation to different Before performing any maintenance operation, disconnect the appliance from
types of gas
the gas supply and electricity network.
Replacing the gas nozzles to operate with another type of gas:
Follow the instructions below to change the burner nozzles on the work
surface:
- Isolate the appliance from the electric outlet to avoid any type of electric contact.
- Remove the grids from the work surface.
- Remove the burners.
- Unscrew the nozzles using a 7 mm spanner, and replace them (Fig.4) with those
needed for the new type of gas according.
Fig 4
Follow the instructions below to change the oven burner nozzle (model 90x60
single oven):
- Remove the oven level (Fig.5).
- Loosen the screw V and pull out the burner from the support being careful not to
damage the ignition plug and the thermocouple (Fig. 6).
- Unscrew the nozzle R using a 10 mm spanner and replace it with the nozzle
needed for the new type of gas according.
Fig 5 Fig 6
Follow the instructions below to change the oven burner nozzle (model 60x60
single oven):
Remove the oven level (Fig.7).
- Loosen the screw V and pull out the burner from the support being careful not to
damage the ignition plug and the thermocouple (Fig.7).
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bertazzoni HER90 6 MFE SNET at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bertazzoni HER90 6 MFE SNET in the language / languages: English as an attachment in your email.

The manual is 1,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bertazzoni HER90 6 MFE SNET

Bertazzoni HER90 6 MFE SNET Usermanual and installation guide - Dutch - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info