605228
4
Zoom out
Zoom in
Previous page
1/40
Next page
4
APPLIANCE MAINTENANCE
ATTENTION: IMPORTANT WARNINGS
For cookers resting on a base
ATTENTION: If the cooker rests on a base, take the measures necessary to prevent the cooker from sliding
along the support base.
For cookers with electric ovens
The unit becomes hot during use. Do not touch the heating elements inside the oven.
For cookers with electric ovens
ATTENTION: The accessible parts can become hot during use. Keep children away from the appliance.
For the food warmer compartment (or drop leaf in our case)
ATTENTION: The internal parts of the food warmer can become hot during use.
For glass doors
Do not use abrasive cleaning products or metal spatulas with sharp edges to clean the oven door’s glass
since this could scratch the surface and the glass could break.
Do not use steam cleaners to clean the appliance.
Replacing parts Before performing any maintenance operation, disconnect the appliance from the
gas supply and electricity network.
To replace parts such as knobs and burners, just remove them from the seats
without disassembling any part of the cooker.
To replace the oven bulb, just unscrew the protection cap that projects out inside the
oven.
Fig.2
WARNING: Before replacing the bulb, disconnect the appliance from the electric
power supply.
WARNING: The power cord supplied with the appliance is connected to that
appliance with an X type connection (in compliance with standards EN 60335-1, EN
60335-2-6 and subsequent amendments) for which it can be installed without the
use of special tools, with the same type of cord as the one installed.
If the power cord becomes worn or damaged, replace it based on the information
reported in types of power cords paragraph .
WARNING: If the power cord is replaced, the installer shall ensure that the ground
cable is longer than the phase cables and also shall comply with the warnings
regarding the electric connection.
To replace the power cable, lift the terminal board’s cover and replace the cable. To
access the terminal board in cookers with a 3x2.5mm² cable, the back panel on the
rear of the appliance must be removed. The power cord should be replaced only by
qualified personnel.
Before disposing of the packaging, please ensure you have removed all the
components.
The up-stand is packed separate and is taped to the back of the cooker. Other
components can be found inside the ovens. All packaging and covering films must
be removed before the installation can commence.
All electric cookers should be installed by a qualified electrician in accordance with
IEE regulations and local electricity provider rules. Building regulations must be
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bertazzoni HER90 6 MFE SNET at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bertazzoni HER90 6 MFE SNET in the language / languages: English as an attachment in your email.

The manual is 1,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bertazzoni HER90 6 MFE SNET

Bertazzoni HER90 6 MFE SNET Usermanual and installation guide - Dutch - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info