508645
108
Zoom out
Zoom in
Previous page
1/148
Next page
108
BSR
BSR (BERNINA Stitch Regulator) Function
The BSR presser foot reacts to the movement of the fabric under the foot and controls the
speed of the sewing computer up to the maximum speed possible. The following applies:
the faster the fabric is moved the higher the speed of the sewing computer.
If the fabric is moved too fast an acoustic signal (beep) is heard, and the red light of the
Start-/Stop Button flashes. The beeper can be turned on or off in the Setup Program or
directly on the «BSR» screen.
BSR Description
By activating the BSR function the sewing
computer sews either continuously at a
reduced motor speed (mode 1, standard),
or as soon as the fabric is moved (mode 2).
As long as the BSR presser foot is illumi-
nated red, adjustments like threading and
changing the needle, for example must not
be carried out, as the needle will engage
while fabric is moved unintentionally!
Without fabric feed the BSR mode is
turned off after approx. 7 seconds and the
red light goes off.
Please refer to the Safety Instructions!
When exceeding a certain speed, adhering to
regular stitch length cannot be guaranteed.
Make sure that the lens on the bottom of
the BSR foot is not dirty (fingerprints, etc.).
Clean lens periodically with soft, slightly
damp cloth.
For an even sewing start (one single stitch)
the foot control must be pressed and the fabric
moved simultaneously.
This also applies for sewing points and
straight stitching within a round form.
If the BSR function is deactivated and later
re-activated without the sewing computer
being switched off in between, the last
selected BSR mode is active.
With Straight Stitch no. 1
This function using a special presser foot allows for Free
Motion quilting (sewing) using the straight stitch and a
pre-selected stitch length (up to 4mm).
A regulated set stitch length is maintained within a certain
speed, independent of the movement of the fabric.
With Zigzag Stitch no. 2
The zigzag stitch can be used for thread painting or fabric
embellishment.
The set stitch length will not be maintained when sewing
with the zigzag stitch, but the BSR function simplifies
the application.
BSR function can be sewn in 2 separate
modes of operation
BSR mode 1 is the active standard
the sewing computer runs continuously at a reduced
motor speed, as soon as the foot control or the Start/
Stop Button is pressed
moving the fabric under the foot will engage the sewing
computer to accelerate
through the continuous needle movement securing in
the same position is possible without pressing an
additional button
touch the button «BSR2» to engage BSR mode 2
the sewing computer will only engage if the foot control
or the Start/Stop Button is pressed and the fabric is
moved simultaneously
the movement of the fabric determines the sewing
speed
for securing, the «Securing Function» button must be
pressed
touch the button «BSR1» to engage BSR mode 1
032298.53.04_1204_B820_EN
108


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bernina 820 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bernina 820 in the language / languages: English as an attachment in your email.

The manual is 27,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bernina 820

Bernina 820 User Manual - German - 216 pages

Bernina 820 User Manual - Dutch - 148 pages

Bernina 820 User Manual - French - 148 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info