508645
30
Zoom out
Zoom in
Previous page
1/148
Next page
30
Overview
Function Buttons
Start/Stop Button
starts and stops the sewing computer when
operating it without foot control
slightly raise the presser foot when turning or
moving the project while sewing - hover
position
Quick Reverse Button/Backstepping
secures the seam beginning and end: sews in
reverse as long as the button is pressed
used to program the buttonhole length
used to program the darning length
used to determine end of stitching in straight
stitch Securing stitch no. 5
used for securing in Quilters Securing
Program no. 1324
switching for accurate stitch-by-stitch back-
stepping (exact retracing of the last 200
needle penetrations)
Pattern End
a stop symbol which appears during sewing
indicates that the function is activated
sewing computer stops at the end of the active
single pattern or the active pattern of a
combination
Automatic Thread Cutter
upper and lower threads are cut automatically
2-6 securing stitches can be programmed in
the setup program - these are sewn before the
thread is cut
Automatic Needle Threader
touch button = completes the threading
process and threads the needle
Needle Stop Up/Down
In the default setting the needle symbol is
displayed above the presser foot indicator.
touch the button briefly:
the needle is raised or lowered (as when
tapping the foot control with your heel)
touch the button longer:
the needle is lowered, the needle symbol is
displayed below
the sewing computer stops with the needle
down
this becomes your default setting
touch the button longer again:
the needle is raised, the needle symbol is
displayed above
the sewing computer stops with the needle
up
Double, triple and wing needles require
manual threading after the Automatic Needle
Threader button has been pressed.
Use the automatic needle threader for needle
sizes 70 - 120. Metallic threads, thick threads
like cordonnet and difficult to work with
threads should be threaded by hand.
When using metallic or cordonnet thread,
use the thread cutter on the head frame
only.
The automatic threader mustn‘t be
activated with one of these presser feet
attached:
nos. 50, 55, 80, 85 and 86.
032298.53.04_1204_B820_EN
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bernina 820 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bernina 820 in the language / languages: English as an attachment in your email.

The manual is 27,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bernina 820

Bernina 820 User Manual - German - 216 pages

Bernina 820 User Manual - Dutch - 148 pages

Bernina 820 User Manual - French - 148 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info