508641
46
Zoom out
Zoom in
Previous page
1/67
Next page
1
2
3
4
5
6
7
8
2
6
7
8
3.1. Threading 4/3 Thread OL (Stitch No 1-8)
3.1. Enhebrado de overlock de 4/3 hilos (punto N°.1-8)
3.1. Einfädeln 4/3 Faden OL (Stich No.1-8)
3.1. EnÞ lage du point de surjet à 4/3 Þ ls (point no.1-8)
44
3
3. Right-hand needle, green markings
Turn the handwheel in the normal direction (as indicated by the arrow)
until the red stop mark is completely centered in the window.
Place the spool on the spool holder pin as illustrated.
(1) Bring the thread up from the spool and lay it from the back to the front
into the guide.
(2) Thread the Þ rst machine guide.
(3) Slip the thread through the groove.
(4, 5) Take the thread under the thread guide plate and through the lower
take up.
(6) Thread the guide.
(7) Thread the guide on the needle clamp.
(8) Thread the right needle from front to back (use automatic needle
threader as explained on page 33).
(9) Place the thread underneath the presser foot.
3. Aguja derecha, marcas verdes
Gire el volante en la dirección de la ß echa hasta que la marca roja Stop
esté exactamente en el centro de la ventana de indicación de la posición
del volante.
Colocar la bobina en el perno del porta-bobinas conforme la ilustración.
(1) Coger el hilo de la bobina y pasarlo de atrás hacia adelante por el
guía-hilo.
(2) Enhebrar la primera guía de la máquina.
(3) Pasar el hilo a lo largo de la ranura.
(4, 5) Colocar el hilo por debajo de la placa-guía y en el tira-hilo inferior.
(6) Enhebrar la guía.
(7) Enhebrar la guía en el porta-agujas.
(8) Enhebrar la aguja derecha de adelante hacia atrás (utilice el
enhebra-agujas automático, como descrito en la página 33)
(9) Colocar el hilo debajo del prensatelas.
3. Rechte Nadel, grüne Markierungen
Drehen Sie das Handrad in der vom Pfeil angegebenen Richtung bis
die rote Stop - Marke genau im Fenster der Handrad - Positionsanzeige
zentriert ist.
Fadenspule anleitungsgemäss auf den Spulenhalterstift stecken.
(1) Faden von der Spule aufnehmen und von hinten nach vorne in die
Führung legen.
(2) Erste Maschinenführung einfädeln.
(3) Faden der Rille entlang führen.
(4, 5) Den Faden unter die Führungsleiste und in den unteren
Fadengeber legen.
(6) Führung einfädeln.
(7) Führung am Nadelhalter einfädeln.
(8) Rechte Nadel von vorne nach hinten einfädeln (Benützen Sie den
Autmatischen Nadeleinfädler, wie auf Seite 33 beschrieben)
(9) Faden unter den Nähfuss legen.
3. Aiguille de droite, repères verts
Tournez le volant dans le sens de la ß èche jusqu'au stop rouge qui doit
se trouver ensuite exactement au centre dans la fenêtre du volant.
EnÞ cher la bobine sur la broche conformément aux instructions.
(1) Prendre du Þ l à partir de la bobine et le faire passer de l'arrière vers
l'avant dans le guide.
(2) EnÞ ler le premier guide de la machine.
(3) Faire passer le Þ l le long de la rainure.
(4, 5) Guidez le Þ l sous la barre guide et dans le donneur de Þ l inférieur.
(6) Faire passer le Þ l dans le guide.
(7) Faire passer le Þ l dans le guide du porte-aiguille.
(8) EnÞ ler l'aiguille de droite, d'avant en arrière. (pour l'utilisation de
l'enÞ le-aiguilee automatique voir page 33)
(9) Glisser le Þ l sous le pied-de-biche.
46


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bernina 1200MDA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bernina 1200MDA in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 1,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bernina 1200MDA

Bernina 1200MDA User Manual - Dutch, Italian - 66 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info