508639
41
Zoom out
Zoom in
Previous page
1/62
Next page
1
2
3
4
5
6
7
8
2
7
8
6
3.1. Einfädeln 4/3 Faden OL (Stich No.1-8)
3.1. EnÞ lage du point de surjet à 4/3 Þ ls (points no.1-8)
3.1. InÞ latura punto overlock a 4/3 Þ li (punto n.1- 8)
3.1. Inrijgen 4/3-draads overlock (steek nr.1-8)
40
3
3. Rechte Nadel, grüne Markierungen
Drehen Sie das Handrad in der vom Pfeil angegebenen Richtung bis
die rote Stop - Marke genau im Fenster der Handrad - Positionsanzeige
zentriert ist.
Fadenspule anleitungsgemäss auf den Spulenhalterstift stecken.
(1) Faden von der Spule aufnehmen und von hinten nach vorne in die
Führung legen.
(2) Erste Maschinenführung einfädeln.
(3) Faden der Rille entlang führen.
(4, 5) Den Faden unter die Führungsleiste und in den unteren
Fadengeber legen.
(6) Führung einfädeln.
(7) Führung am Nadelhalter einfädeln.
(8) Rechte Nadel von vorne nach hinten einfädeln (Benützen Sie den
Autmatischen Nadeleinfädler, wie auf Seite 33 beschrieben).
(9) Faden unter den Nähfuss legen.
3. Aiguille de droite, repères verts
Tournez le volant dans le sens de la ß èche jusqu'au stop rouge qui doit
se trouver ensuite exactement au centre dans la fenêtre du volant.
EnÞ cher la bobine sur la broche conformément aux instructions.
(1) Prendre du Þ l à partir de la bobine et le faire passer de l'arrière vers
l'avant dans le guide.
(2) EnÞ ler le premier guide de la machine.
(3) Faire passer le Þ l le long de la rainure.
(4, 5) Guidez le Þ l sous la barre guide et dans le donneur de Þ l inférieur.
(6) Faire passer le Þ l dans le guide.
(7) Faire passer le Þ l dans le guide du porte-aiguille.
(8) Enhebrar la aguja derecha de adelante hacia atrás (utilice el
enhebra-agujas automático, como descrito en la página 33).
(9) Glisser le Þ l sous le pied-de-biche.
3. Ago destro, marcature verdi
Girare il volantino nella direzione indicata dalla freccia, Þ nché appare la
marcatura rossa nell’oblò dell’indicatore del volantino.
Mettere la spoletta sul perno porta-Þ lo.
(1) Tirare il Þ lo dalla spola ed passarlo da dietro in avanti nella guida
dell’asta.
(2) InÞ lare la prima guida della macchina.
(3) Portare il Þ lo lungo la fessura.
(4, 5) Passare il Þ lo sotto il listello guida e sopra il tendiÞ lo inferiore.
(6) InÞ lare la guida.
(7) InÞ lare la guida sul morsetto dell’ago.
(8) InÞ lare l’ago destro da davanti (adoperare l’inÞ latore automatico come
descritto a pagina 33).
(9) Mettere il Þ lo sotto il piedino.
3. Rechternaald, groene markeringen
Draai het handwiel in de door de pijl aangegeven richting tot de rode
stop-markering precies in het venster van de handwielpositie-indicator is
gecentreerd.
Garenklos zoals afgebeeld op de kloshouderstift zetten.
(1) Draad vasthouden en van achter naar voor in de geleiding leggen.
(2) Eerste machinegeleiding inrijgen.
(3) Draad door de gleuf trekken.
(4, 5) Leg de draad onder de geleidingsrand en in de onderste draadhevel.
(6) Geleiding inrijgen.
(7) Geleiding aan de naaldhouder inrijgen.
(8) Rijg de rechternaald van voor naar achter in (gebruik de automatische
naaldinrijger, zoals op blz. 33 beschreven).
(9) Draad onder de naaivoet leggen.
41


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bernina 1150MDA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bernina 1150MDA in the language / languages: Dutch, Italian as an attachment in your email.

The manual is 1,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bernina 1150MDA

Bernina 1150MDA User Manual - English, German, French, Spanish - 62 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info