508639
18
Zoom out
Zoom in
Previous page
1/62
Next page
2.1. Basic Operating Procedures / 2.1. Manejo
2.1. Bedienung / 2.1. Commandes
17
2
C
D
Changing the presser foot
• Switch the machine off (power
switch "0")
• Raise the presser foot.
• Raise the needles. Turn the handwheel
in the normal direction (as indicated by
the arow) until the red stop mark of the
handwheel indicator is centered in the
window.
Press the catch (C) to release the presser
foot from the clamp. Raise the presser
foot shank to the highest position (B) and
remove the presser foot to the left. To
attach the presser foot, place it under the
shaft. The groove in the shaft should line up
exactly with the presser foot pin (D). Lower
the shank and the presser foot will engage
automatically.
(E) Blind stitch foot
(F) Elasticator
Cambio del prensatelas
• Desconectar la máquina, interruptor
principal a „О“.
• Subir el prensatelas.
• Subir las agujas. Girar el volante en su
dirección normal (como indica la flecha)
hasta que la marca roja del volante
aparezca en el centro de la ventana de
indicación de la posición del volante.
Apretar la palanca (C). El prensatelas se
desengancha de su sujeción. Apretar la
palanca alza-prensatelas hasta arriba del
todo (B) y sacar el prensatelas por la parte
izquierda. Para enganchar el prensatelas,
situarlo debajo del vástago. La ranura del
vástago tiene que estar exactamente sobre
el perno del pie (D). Bajar el vástago, el pie
se engancha.
(E) Prensatelas para punto invisible
(F) Prensatelas par coser cinta elástica
Nähfuss auswechseln
• Maschine ausschalten, Hauptschalter
auf „О“ stellen.
• Nähfuss hochstellen.
Nadeln anheben. Handrad in der auf
der Verschalung angegebenen Richtung
drehen, bis die rote Marke an der Handrad
Positionsanzeige ganz im Fenster sichtbar
ist.
Auslösehebel (C) drücken. Der Nähfuss
löst sich aus seiner Halterung. Den
Nähfusslifterhebel ganz nach oben drücken
(B) und den Nähfuss nach links wegziehen.
Zum Befestigen, den Nähfuss unter den
Schaft legen. Die Rille des Schaftes soll
dazu genau über dem Stift des Nähfusses
liegen (D). Den Schaft senken, der Nähfuss
rastet ein.
(E) Blindstichfuss
(F) Gummibandeinnähfuss
Remplacement du pied-de-biche
• Couper le circuit de la machine en
mettant le commutateur principal sur „О“.
• Relever le pied-de-biche.
• Relever l'aiguille. Tourner le volant dans la
direction indiquée sur le bâti jusqu'à ce que
le repère rouge de l'afÞ chage de la position
du volant soit parfaitement visible dans la
fenêtre.
Presser le levier de libération (C). Le pied-
de-biche se libère de son support. Presser
le levier du pied-de-biche tout à fait en
haut (B), puis retirer le pied-de-biche par la
gauche. Pour Þ xer le pied-de-biche, le poser
sous la tige. Pour cela, la rainure de la tige
doit être exactement au-dessus de la tige
du pied-de-biche (D). Abaisser la tige, le
pied-de-biche s'encliquette.
(E) Pied pour ourlet invisible
(F) Pied pour la pose de ruban élastique
E
F
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bernina 1150MDA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bernina 1150MDA in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 1,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bernina 1150MDA

Bernina 1150MDA User Manual - Dutch, Italian - 62 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info