474163

Berner GA401 Manual

6
Zoom out
Zoom in
Previous page
1/67
Next page
ENGLISH
CONTENTS PAGE
A Supplied Items 2
B Required Tools for Installation 2
1 Important Notes 7
1.1 Important safety instructions 7
1.1.1 We shall be exempt from our warranty
obligations and product liability in the event that 7
1.1.2 Checking the door / door system 7
1.2 Important instructions for safe installation 7
1.2.1 Prior to installation 7
1.2.2 In carrying out the installation work 7
1.3 Warnings 8
1.4 Maintenance advice 8
1.5 Information on the illustrated section 8
Illustrated section 15-29
2 Installation Instructions 39
2.1 Garage door operator 39
2.2 Required clearance for installing the operator 39
2.3 Door latch on a sectional door 39
2.4 Centrally positioned lock on a sectional door 39
2.5 Off-centred reinforcement profile on a sectional door 39
2.6 Door latches on an up-and-over door 39
2.7 Up-and-over doors with a forged iron door handle 39
2.8 Guiding rail 39
2.9 Prior to installation: guiding rail 39
2.10 Installation: guiding rail 39
2.11 Operation types: guiding rail 39
2.11.1 Manual operation 39
2.11.2 Automatic operation 39
2.12 Establishing the "CLOSE" end-of-travel position
by installing the limit stop 39
2.13 Tensioning the drive medium 40
3 Putting into service 40
3.1 Notes on work involving electrics/electronics 40
3.2 Putting the operator into service 40
3.2.1 Deleting the door data 40
3.2.2 Programming the operator (learning procedure) 40
3.2.3 Setting forces and conduct after a safety shutdown 41
3.2.4 Setting the door speed 41
4 Installation: garage door operator
and accessories 41
4.1 Notes on work involving electrics/electronics 41
4.2 Installing the radio receiver 41
4.3 Connecting an external radio receiver 41
4.4 Electrical connection / Connection clips 41
4.5 Connecting Additional Components / Accessories 42
4.6 Connecting external "impulse" buttons to start or
stop the travel of the door 42
4.7 Connecting internal “impulse“ button IT3b 42
4.7.1 “Impulse” button: start or stop the travel of the door 42
4.7.2 Light button: switch on / off operator lightning 42
4.7.3 Button: switch on / off radio system 42
4.8 Connecting a cutout switch or a wicket door contact 42
4.9 Connecting a photocell 42
4.10 Connecting a 2-wire light barrier 42
4.11 Connecting an electronic switch barth of the
borders 8,2kΩ 42
4.12 Connecting an optosensoric switch barth of the
borders 42
4.13 Connecting a warning lamp 42
4.14 Connecting an external lamp 42
4.15 Connecting a “door closed” display to the
optional relay 42
5 Special functions and any other adjustment
possibilities of the garage door operator 43
5.1 Second opening position (airing position) 43
5.1.1 Programming the second opening position
(airing position) 43
5.2 Defined direction instructions 43
5.3 Quick-opening function 43
5.4 Soft-stop 43
5.5 Short return to the position “door closed” 43
5.6 Automatic door locking 43
5.6.1 Programmable opening time/advance warning time 43
5.6.2 Automatic door locking “closed” 44
5.7 “Door closed”: programmable lightning time 44
6 Operation of the garage door operator 44
6.1 Normal operation 44
6.2 Operation following actuation of the mechanical /
manual release 44
6.3 Operator lighting error message / LED-diagnosis 44
6.4 Measures following error message 45
6.5 Malfunctions and remedy 45
6.5.1 Operator fails to start up 45
6.5.2 Operator fails to work with hand transmitter 45
6.5.3 Operator fails to work with externally connected
controls/buttons 46
6.5.4 Door fails to close or open fully 46
6.5.5 Operator responds but door fails to open 46
6.5.6 The closing door changes direction 46
6.5.7 Lights damaged 46
6.5.8 Radio system: range too low 46
7 Terms and Conditions of the Warranty 46
8 Technical Data 46
9 Dismantling and Disposal 47
10 Circuit Board Overview 48
Copyright.
No part of this instruction manual may be reproduced
without our permission.
Subject to changes.
6
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Berner GA401 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Berner GA401 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 5,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info