474161

Berner GA201 Manual

48
Zoom out
Zoom in
Previous page
1/67
Next page
ENGLISH
$)0switchesfUNcTIONs3#(
3TOPbutton
,Ight barrier
/.
No
No
/&&
yes
yes
$)0switchesfUncTIONs3#(
,Ight barrier
Evaluationprotection of closing borders
/.
wire
/3
/&&
CONTAcT
K
Quickopening
3OFTstop
 
,%$Display
,%$Red
,%$GReen
glows flashes
,%$
,%$
3#(3#(
/.


/.
factory settingfactory setting


/3barthactivated
,Ight barrier activated
-OTORgoes to "CLOSE"
-OTORgoes to "OPEN"
K
barthactivated
3TOP circuitinterrupted
8
83
.^6
(Z
0
-
,$

,$
).)
,+
4%34
67
3OCKEt'
,$,$
+,
34 3434
43
3#(
3#(
./
/.

  
$EFIned direction instructions
Light at "CLOSED"
yes
yes
No
yes No
No
Short return to the position "door CLOSED"
External light: light function (1), warning function (2)
LoNG
1
short
2

Circuit board overviewaNDshort instructions of programming

Brief instructions learning procedure




Press the black button until the lamp starts flashing. Allow
to flash twice, then release the "learn" button
Press white operating button until door travels to its "OPEN"
pOSITION (permanent contact)
Briefly press black button
Door closes, opens and closes twice automatically
The operator is now programmed
0ROGRAMMing operator light at door closed,
durationsEc




Unplug from the mains
Press black buttonDRàCKENpermanent contact
Plug back into the mains while keeping "learn" button pressed
After the operator lamp has switched on, release the "learn"
buttonOn repeating the procedure the factory settings
doorclosedsEcare active again
Brief instructions second opening position




Press the black button until the lamp starts flashing
twice
Additonally press the white button until the lamp flashes
more quickly, the release both buttons
Open the door with the white buttonpermanent contact
until the desired "second opening" position is reached
Briefly press the black button
The "second opening" position is programmed
0ROGRAMMINGautomatic timer / early warning phase




Briefly press black buttonLamp flashes times
Wait till the desired open phase is overMAXsEcthen
briefly press black button
Wati for early warning phase to be setsEcThe lamp
flashes beyondXThen again press black button
Automatic timer / early warning phase has now been
programmed
To switch out the automatic closure briefly press black button
consecutively
48
… 48 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Berner GA201 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Berner GA201 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 5,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info