474161

Berner GA201 Manual

8
Zoom out
Zoom in
Previous page
1/67
Next page
ENGLISH
The clearance between the highest point of the door and
the ceiling (also when the door is opening) must be at
least 30 mm (see fig. 1.1a / 1.1b). If there is inadequate
clearance, the operator may also be installed behind the
opened door, provided sufficient space is available. In
such instances an extended door link arm must be used.
The garage door operator can be positioned off-centre by
max. 50 cm, the exception being sectional doors with
high-lift tracks (track application "H"), where a special
track fitting is required.
The required shockproof electric socket allowing the
operator to be connected to the electricity supply should be
installed at a distance of approx. 50 cm from the operator
head.
Please check these dimensions!
1.3 Warnings
Permanently installed controls (such
as buttons or similar devices) should
be installed within sight of the door
but well away from any moving parts
and at a height of at least 1.5 metres.
It is vital that they are installed out
of the reach of children!
Note
A caution notice warning about the trap risk must be
permanently fixed in a conspicuous place close to the
permanently installed buttons used to actuate the operator.
Make sure that
- neither persons nor objects are located
within the door's range of travel.
- children do not play around with the
door system!
- the cord of the mechanical release on the
carriage cannot get caught up in the
ceiling's support system or in any other
protruding parts of vehicles or the door.
ATTENTION
For garages without a second entrance, an
emergency release must be fitted to ensure
that is no danger of getting locked in.
This must be ordered separately and its function
checked once a month.
ATTENTION
Do not allow anyone to hang bodily from the pull
cord with knob!
1.4 Maintenance advice
The garage door operator is maintenance-free. For your
own safety, however, we recommend that you have the
door system checked according to manufacturer
information by service engineers qualified to inspect
and service garage doors.
Inspection and maintenance should only be effected by a
competent person, please contact your supplier for this. A
visual inspection can be effected by the operator.
Regarding necessary repairs contact your supplier. We
shall accept no responsibility for improper and
unprofessional repairs.
1.5 Information on the illustrated section
The illustrated section shows installation of the operator
on an up-and-over door.
Where installation differs for a sectional door, this is
shown in addition.
In this instance, letters are assigned to the figures
as follows:
is assigned to the sectional
door and
to the up-and-over door.
Some of the figures also include the symbol shown below
together with a text reference. This refers to specific text
in the ensuing text section to provide you with important
information regarding installation and operation of the
garage door operator.
Example:
= see text section, point 2.2
Furthermore, the following symbol, which marks factory
settings, is illustrated in the picture section and text section
which explain the menu of the operator.
= factory settings
Copyright.
No part of this instruction manual may be reproduced
without our permission.
Subject to changes.
8
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Berner GA201 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Berner GA201 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 5,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info