680430

Berner DA40 Manual

27
Zoom out
Zoom in
Previous page
1/168
Next page
Table of Contents
A Articles supplied ..................................................... 2
B Tools needed for assembly .................................... 2
1 About These Instructions ..................................... 28
1.1 Further applicable documents ................................ 28
1.2 Warnings used ........................................................ 28
1.3 Definitions used ...................................................... 28
1.4 Symbols and abbreviations used ........................... 28
1.5 Abbreviations used ................................................. 29
2
Safety Instructions ........................................ 29
2.1 Intended use ........................................................... 29
2.2 Inappropriate use .................................................... 29
2.3 Fitter qualification ................................................... 29
2.4 Safety instructions for fitting, maintenance,
repairs and disassembly of the gate system .......... 29
2.5 Safety instructions for fitting ................................... 29
2.6 Safety instructions
for initial start-up and for operation ........................ 30
2.7 Safety instructions for using
the hand transmitter................................................ 30
2.8 Safety instructions for inspection
and maintenance .................................................... 30
2.9 Approved safety equipment.................................... 30
3 Fitting ..................................................................... 30
3.1 Preparation for fitting .............................................. 30
3.2 Fitting the gate operator ......................................... 30
3.3 Fitting the operator control ..................................... 32
3.4 Mains voltage .......................................................... 32
3.5 Connecting the operators ....................................... 32
4 Initial Start-Up of Basic Equipment,
Gate System Recording the CLOSE
End-of-Travel Position via the Limit Switch
(Factory Setting) .................................................... 33
4.1 Single-leaf gate system .......................................... 33
4.2 Double-leaf gate system ......................................... 34
5 Initial Start-Up of Basic Equipment,
Gate System Recording the CLOSE
End-of-Travel Position via Mechanical
End Stops or an Electric Lock ............................. 36
5.1 Single-leaf gate system .......................................... 36
5.2 Double-leaf gate system ......................................... 36
6 Gate systems that open outwards ...................... 38
6.1 Connecting the operators ....................................... 38
6.2 Using end stops ...................................................... 38
6.3 Using limit switches ................................................ 38
6.4 Teaching in the end-of-travel
positions and forces ............................................... 38
7 Further Work ......................................................... 38
7.1 Force learning runs ................................................. 38
7.2 Connecting safety equipment ................................ 38
7.3 Connecting additional components/accessories ... 39
7.4 Setting additional functions via the DIL switches ... 40
8 Radio ...................................................................... 42
8.1 Hand transmitter BDS140 ...................................... 42
8.2 External receiver ..................................................... 43
9 Operation ............................................................... 44
9.1 Instructing users ..................................................... 44
9.2 Normal operation .................................................... 44
9.3 Reversing during an opening run ............................ 44
9.4 Reversing during a closing run ............................... 44
9.5 Behaviour during a power failure
(withoutemergency battery) ................................... 44
9.6 Behaviour following a power failure
(without emergency battery) ................................... 44
9.7 Disengaging without a power failure....................... 44
9.8 Factory reset ........................................................... 44
9.9 Operation, error and warning messages ................ 44
9.10 Error acknowledgement .......................................... 45
10 Inspection and Maintenance ............................... 45
11 Optional Accessories ........................................... 46
12 Dismantling and Disposal .................................... 46
13 Warranty Conditions ............................................. 46
13.1 Performance ........................................................... 46
14 Excerpt from the Declaration
of Incorporation .................................................... 46
15 Technical Data ....................................................... 47
16 Overview of DIL Switch Functions ...................... 48
Dissemination as well as duplication of this document and the
use and communication of its content are prohibited unless
explicitly permitted. Noncompliance will result in damage
compensation obligations. All rights reserved in the event of
patent, utility model or design model registration. Subject to
changes.
Illustrated section ..................................... 145
DA20_DA40 V2 RE / Rev. 1.2 / 08.2014 27
ENGLISH
… 27 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Berner DA40 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Berner DA40 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 8,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info