673666
14
Zoom out
Zoom in
Previous page
1/17
Next page
900 Series 932-933 - 14 - Date 25-03-08 UM - Code SC1 - Rev. 0.1
User Manual
5.1 Sharpening device
Every sharpening device is marked with the serial number of the machine.
Only this sharpening device may be used for sharpening.
Usage of other sharpening devices can cause serious injuries or damage the machine. Never use
another sharpening device.
The sharpening device is equipped with 1 stone for sharpening and 1 stone for taking off the burr
(deburring)
Always clean the machine before sharpening, as the stones will then loose their efficiency if they become
contaminated by meat waste and fats. In case this should happen, clean the stones carefully with washing
liquid and a wire brush.
5.2 Mounting the sharpening
device
Open the thickness plate
completely.
Position the carriage in the centre
of the machine
Lift up end piece holder
Mount the sharpening device to
the thickness plate so that the
cone of the sharpening device fits
into the slit on the bottom of the
thickness plate (direction of arrow)
Pull out the pin on top of the
sharpening device in direction of
arrow and move the sharpening
device over the edge of the
thickness plate.
Move the sharpening device with
the pulled out pin to the front in
direction of the blade (direction of
arrow), so that the pin is engaged in the hole of the thickness plate.
The sharpening stones are now in the correct position, i.e. the blade edge is positioned between the two
sharpening stones.
5.3 Sharpening the blade
Switch on the machine
Turn the yellow handwheel of the sharpening device in direction 1. The
sharpening stone is sharpening the blade by being in contact with the blade.
Approximately 15 seconds are enough to sharpen correctly
Switch off the machine
Check if there is a visible burr at the edge of the blade
If not: Sharpen again
Switch on the machine again
To take off the burr turn the yellow handwheel in direction 2. Now both stones are
touching the blade.
Approximately 2 seconds is enough to take off the burr.
Switch off the machine
When the sharpening procedure is completed turn the yellow handwheel to 0.
0
1
2
15 sec.
< 2 sec.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Berkel 900 Series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Berkel 900 Series in the language / languages: English as an attachment in your email.

The manual is 0,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info