673666
11
Zoom out
Zoom in
Previous page
1/17
Next page
900 Series 932-933 - 11 - Date 25-03-08 UM - Code SC1 - Rev. 0.1
User Manual
Special notes regarding slicing of end pieces of food products:
Before placing the remaining piece of the food product in the carriage you have to cut off the pointed end.
Otherwise the food product cannot be held correctly by the end piece holder. It is even better to turn the
original cutting side of the food product to the end piece holder.
Attention! Risk of getting hurt!
Never try to hold the food product by hand, there is a risk of serious injury!
Always use the end piece holder.
If a product has been sliced using the end piece holding as a clamp on top of the meat, and the meat piece
is reduced the clamping procedure can no longer be used. The end piece holder should now be placed
behind the meat product to hold the meat as follows:
Switch off the machine.
Check if the adjusting bar is fixed.
Lift up the end piece holder
Place the end piece into the carriage as described below
3.8. Slicing end pieces
Pull the carriage backwards for loading the carriage when the machine is
adjusted for manual operation.
Lift up end piece holder
Lay the food product against the back of the carriage.
Adjust the adjusting fence (bar) according to the size of the food product.
Place the end piece holder behind the food product.
Adjust the thickness of the slices with the thickness knob.
Choose automatic or manual operation (see 3.4)
The machine can now be used in automatic or manual mode (as in 3.6 above)
Attention! Never try to load the carriage while it is moving automatically. Always switch off
the machine first, otherwise there is a risk to get injured!!
4. Cleaning
Before initial operation and after if the machine has not been used for a long period the machine should be
cleaned carefully and thoroughly
When the machine is used regularly it should be cleaned at least once a day or if necessary a few times a
day. For cleaning proceed as follows:
Risk of getting hurt!
Be careful when cleaning the machine. Especially in the area of the knife there is a risk of injury.
Always work with concentration, do not let distract yourself from your work.
4.1. How to proceed with cleaning
Switch off the machine at the red main switch.
Adjust machine to manual operation
Pull off the plug.
Close the thickness plate completely by turning the thickness knob
clockwise
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Berkel 900 Series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Berkel 900 Series in the language / languages: English as an attachment in your email.

The manual is 0,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info