779528

Bergamont TIME TRIAL MACHINE 2019 Manual

14
Zoom out
Zoom in
Previous page
1/63
Next page
ENGLISH ENGLISH
ROAD BIKE | OWNER’S MANUALOWNER’S MANUAL | ROAD BIKE
b ca e fd
| 26 2 7 |
You will feel an increasing resistance at the lever. Only turn the axle until it is
hand-tight.
Make sure the RWS quick-release lever does not stand out to the front (d). Open the
RWS quick-release lever a little (e, position 1) to bring it into a favourable position.
Turn the RWS quick-release lever then into the desired position (e, position 2) and
re-close it towards the hub (e, position 3).
Actuate the brake lever to make the brake work. Lift the wheel and give it a strong tap
from above. The wheel must be securely fixed and must not rattle.
Wheel removal
Turn the quick-release lever anticlockwise to open the RWS system. Release the thru
axle completely by two and a half turns, hold the wheel in its position and remove the
axle from the hub.
DANGER!
G
Improperly mounted wheels may throw you off your bike or result in serious
accidents! Therefore, if you have the slightest doubt, contact your BERGAMONT
dealer and ask him to explain the system of your BERGAMONT bike to you.
DANGER!
G
After wheel mounting test the brakes in stationary. You should reach the pressure
point of the brake before the brake lever reaches the handlebars. In the case of
hydraulic brakes pump them, if necessary, until you reach a precise pressure point (f).
DANGER!
G
Do not open the red screw to open or close the RWS system.
NOTE!
I
Before mounting or replacing a fork/wheel combination with thru-axle system, be
sure to read first the manuals of the respective fork or wheel manufacturer. More
information are also provided at www.dtswiss.com
THRU AXLES ON THE BERGAMONT BIKE
The RWS system from DT Swiss/SYNCROS (a-c) for road racing and cyclo-cross
racing bikes used by BERGAMONT are thru axles which provide the forks and the
rear frames with a higher stiffness. Whenever your BERGAMONT bike is exposed to
high loads, it remains directionally stable.
In the case of BERGAMONT road or cyclo-cross bikes with disc brakes the RWS
system is screwed on the right side. The system has a larger thread and can be
released with no more than two and a half turns. Make sure during the assembly that
the thru axles, the drop-outs of the fork and the hubs are clean. Clean the compo-
nents with an absorbent cloth, if necessary, by using water and a little detergent.
In case you do not succeed in adjusting and fixing the wheel, as described, contact
your BERGAMONT dealer.
Safe fastening of components with a quick-release
Wheel mounting
Put the wheel into the fork or the rear frame and mount the rotor simultaneously, if
necessary, in the brake calliper. Make sure that in the area of the rear wheel the chain
runs over the sprockets and over both pulleys of the rear derailleur.
Bring the front wheel into the right position between the drop-outs and slide the thru
axle with open quick-release lever from the left side through the drop-out and the
hub.
As soon as you have reached the opposite side, turn the thru axle clockwise into
the nut on the right side. Do not apply force, but make sure the axle thread engages
properly with the nut on the other side.
During the first turn you should be able to turn the RWS quick-release lever of the thru
axle nearly without resistance. If everything fits, turn the RWS quick-release lever all
in all two and a half turns clockwise to pre-tighten the RWS system.
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bergamont TIME TRIAL MACHINE 2019 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bergamont TIME TRIAL MACHINE 2019 in the language / languages: English as an attachment in your email.

The manual is 9.03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bergamont TIME TRIAL MACHINE 2019

Bergamont TIME TRIAL MACHINE 2019 User Manual - German - 65 pages

Bergamont TIME TRIAL MACHINE 2019 User Manual - French - 64 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info