657619
16
Zoom out
Zoom in
Previous page
1/64
Next page
30 31
ENGLISH
ENGLISH
ROAD BIKE | OWNERS MANUAL 2016
OWNERS MANUAL 2016 | ROAD BIKE
DANGER!
G
Make sure not to overtighten the binder bolt of the seat post clamp. Other-
wise you may damage the seat post or the frame. Risk of accident!
CAUTION!
A
If the seat post does not move easily inside the seat tube or if it cannot be
tightened sufficiently, ask your BERGAMONT dealer for advice. Do not use
brute force!
CAUTION!
A
Tighten carefully by approaching the prescribed maximum torque value in
small steps (0.5 Nm increments) and check in between the proper fit of the
component. Never exceed the maximum torque value indicated by the manu-
facturer!
NOTE!
I
Children and adolescents need to have the saddle height and the position
of saddle and handlebars checked at least every 3 months!
ADJUSTMENT OF THE HEIGHT OF THE HANDLEBARS
In principle, BERGAMONT road bikes are sports bikes designed for speed. For
this reason alone a BERGAMONT road bike sets certain basic requirements
to the body, the shoulder and the neck muscles. The height of the handlebars
compared to the saddle and the distance between saddle and handlebars de-
termine how much your upper body will be inclined forward. Lowering the han-
dlebars gives you a streamlined position and brings more weight to bear on the
front wheel. However, it also entails an extremely forward leaning posture which
is tiring and less comfortable, because it increases the strain on your wrists,
arms, back, upper body and neck. As a general rule you should be able to adopt
the three basic positions (d-f) on a BERGAMONT road bike without any prob-
lems with your hands around the respective area on the handlebars.
In the case of BERGAMONT road bikes an Aheadset®-stem allows the vertical
adjustment of the handlebars. This requires special knowledge. In this regard,
the descriptions hereafter may be incomplete. If you are in doubt or if you have
any questions, contact your BERGAMONT dealer.
Align the saddle with the frame by using the saddle nose and the bottom brack-
et or top tube as a reference point. Clamp the seat post tight again by closing
the quick-release, as described in the chapter “Using quick-releases and thru
axles” or by turning the seat post binder bolts clockwise in half turns or better
in steps of 0.5 Nm increments starting at 3 Nm (a). You should not need much
strength in your hands to clamp the seat post sufficiently tight. Otherwise the
seat post does not match the frame.
Verify in between that the seat post is sufficiently tight by taking hold of the
saddle at both ends and then trying to rotate the seat post inside the seat tube
(b). If it does rotate, gently retighten the binder bolt of the seat post clamp by
half a turn or better by a quarter turn or in steps of 0.5 Nm increments and do
the check again.
Does the leg stretch test now produce the correct result? Check by moving your
foot and pedal to the lowest point. When the ball of your foot is exactly above
the pedal centre in the ideal pedalling position, your knee should be slightly
bent. If this is the case, the saddle height is adjusted to the correct height.
Check whether you can touch the ground safely while sitting on the saddle by
stretching your feet to the floor (c). If not, you should lower the saddle until you
can, at least to begin with.
DANGER!
G
Never apply grease or oil into a seat tube of a frame made of carbon unless
an alloy sleeve is inside the frame. If you mount a carbon seat post, do not
put any grease on it, even if the frame is made of metal. Once greased, carbon
components may never again ensure reliable clamping! Use special carbon
assembly paste instead.
DANGER!
G
Never ride your bike with the seat post drawn out beyond the limit, maxi-
mum, or stop mark! The seat post might break or cause severe damage to
the frame. In the case of frames with seat tubes that extend beyond the top of
the frame’s top tube the seat post should be inserted into the seat tube at least
below the bottom of the top tube and below the top of the rear stays! If seat
post and frame require different minimum insertion depths, you should opt for
the deeper insertion depth.
b ca e fd
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bergamont Road Bike at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bergamont Road Bike in the language / languages: English as an attachment in your email.

The manual is 15,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info