657621
23
Zoom out
Zoom in
Previous page
1/41
Next page
44 45
b ca e fd
ENGLISH
ENGLISH
SHORT MANUAL | OWNER`S MANUAL 2016
OWNER`S MANUAL 2016 | SHORT MANUAL
If the saddle rails fit into the clamp grooves, slide the saddle on the seat post
and ensure that the clamp is positioned midway along the total length of the
rails (a). Position the saddle so that its upper surface is parallel to the ground.
Tighten the bolt gradually and make sure
1) the clamping device is still accurately mounted on the carbon seat post head
and
2) the clamp is tightening evenly around each rail.
Once there is uniform hold on both rails, tighten the bolt gradually with a torque
wrench (b) until you have reached the maximum torque value indicated in New-
ton metres (Nm) on the seat post.
DANGER!
G
Check the bolts by using a torque wrench once a month according to the
values indicated directly on the components and/or in the manuals of the
component manufacturers on the enclosed BERGAMONT info CD.
DANGER!
G
Poorly tightened or loosening bolts can fail. Risk of accident!
COCKPIT ADJUSTMENT
Brake lever reach adjustment on BERGAMONT road racing and cyclo-
cross bikes
In particular, riders with small hands should ask their BERGAMONT dealer to
adjust the brake lever position (c), i.e. the position where the brake starts to be
effective, to the length of the riders fingers immediately on purchase.
Some models of various brands allow an adjustment at the brake lever/shifter,
e.g. by means of adjusting bolts or spacers (d). In the case of the other models
the brake cables are clamped according to your wishes at the brake bodies.
Adjusting bolts located in this area only serve to compensate brake pad wear.
Have the lever reach adjusted and make sure the first phalanx of the index
finger reaches around the brake lever/shifter. Check the proper adjustment
and functioning of the brake system subsequently, as described in the chap-
ter “Brakes” in this BERGAMONT short manual as well as in your detailed
BERGAMONT owner’s manual and in the manuals of the component manufac-
turers on the enclosed BERGAMONT info CD.
NOTE!
I
Some manufacturers offer brake levers/shifters which are suitable for small
hands. If you have any problems with the brake lever reach, contact your
BERGAMONT dealer.
Adjustment of handlebar tilt and brake lever/shifter units on
BERGAMONT road racing and cyclo-cross bikes
The straight extensions below the drops should be parallel to the ground or
point slightly downwards towards the rear (e). The grips of the brake lever/shift-
er units are horizontal or point slightly upwards. The ends of the brake lever/
shifter units should meet an imaginary extension of the bottom line of the drops.
Shifting the brake levers/shifters is a job best left to your BERGAMONT dealer,
as it involves retaping the handlebars afterwards.
To adjust the tilt of the handlebars, release the Allen bolt(s) on the underside or
front side of the stem. Turn the handlebars to the desired position. Make sure
the handlebars are accurately centred in the stem.
Carefully retighten the bolt(s) with the torque wrench. Make sure the upper and
lower clamping slots of the stem are parallel and identical in width. If you have a
stem with several bolts, tighten them evenly in a cross pattern by using a torque
wrench and observe the recommended torque values.
Check by trying to rotate the handlebars relative to the stem (f) and tighten the
bolt a little more, if necessary.
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bergamont 2016 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bergamont 2016 in the language / languages: English as an attachment in your email.

The manual is 9,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bergamont 2016

Bergamont 2016 Quick start guide - German - 41 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info