784247
11
Zoom out
Zoom in
Previous page
1/36
Next page
11
Installation
6006113_a – 01.06.2022
EN
Seal the cut surface of the work top with suitable material
(heat resistant to 75 °C – e.g. special paint, silicone rubber
or cast resin).
For the material used, the worktop manufacturers
instructions must be followed.
Place the hob into the specified position in the lower
cabinet from above.
3.3.5 Establish electrical power supply
DWARNING!
Risk of death due to electric shock!
Touching live parts can cause an electric shock, burns or
death.
Ensure that the voltage supply is and remains
disconnected while the following work is in progress.
DATTENTION!
Danger of property damage due to incorrect connection!
If the hob is connected with further devices (e.g. oven),
damage can arise due to overvoltage. The customer must
provide a separate connection point with dedicated fuse for
the hob.
Make sure that the device is connected separately.
Make sure the connection is separately protected with a
circuit breaker and a residual current device.
Observe the voltage specifications on the ratings plate.
Connect the device to the power supply provided by the
customer. The junction box is located on the underside of
the device.
Connection to spring-loaded terminals (e.g. in cooker
connection boxes) is not permitted.
Connection possibilities:
y400 V ~ / 50/60 Hz – 2P+N
NL1L2
45 123
Cable H 05 VV - F, H 05 RR - F,
Diameter 4 x 2.5 mm2,
Fuse 16 A
y230 V ~ / 50/60 Hz – 1P+N
(optional, not compatible with AutoRun module)
NL1
45 123
Cable H 05 VV - F, H 05 RR - F,
Diameter 3 x 4.0 mm2,
Fuse 40 A
Route the cables so that they are not kinked, crushed or
damaged and do not come into contact with hot parts of
the device.
Make sure that the device can be disconnected on all
poles from the electricity supply after installation.
After switching on the power supply, the device is ready for
operation.
3.3.6 Check and carry out commissioning
DATTENTION!
Risk of disruptions due to moisture in the device!
If the device is moved from a cold environment into a hot
one, condensation may form inside.
Wait about 2-3 hours before bringing the device into
service.
Ensure that the device is accessible for maintenance work
at all times.
Check that an all-pole isolating device (min. 3 mm contact
gap) is present.
Check that the mains cable and the electrical connection
cable are not kinked, crushed or damaged.
Make sure that the protective film is removed.
Check the correct functioning of the device.
D“4. Operation (page 12).
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Berbel BKF 90 iPP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Berbel BKF 90 iPP in the language / languages: English as an attachment in your email.

The manual is 7.35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Berbel BKF 90 iPP

Berbel BKF 90 iPP User Manual - German - 36 pages

Berbel BKF 90 iPP User Manual - Dutch - 36 pages

Berbel BKF 90 iPP User Manual - French - 36 pages

Berbel BKF 90 iPP User Manual - Italian - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info