784245
12
Zoom out
Zoom in
Previous page
1/40
Next page
12
Installation
6006361_a – 18.05.2022
yThe device must remain accessible at all times for
maintenance work (e. g. with a removable rear panel or
service cover). The space must be sufficiently large to
allow for removal of the recirculated air filter.
yDuring recirculated air mode sufficiently large ventilation
slots must be available for the ventilation.
yThe air flowing out must be able to dissipate unimpeded.
yIf necessary for the installation, only use suitable hob
protection grates or hob covers.
Please consult your dealer or customer services.
Country-specific, legal provisions must be observed.
3.3 Requirements for individual operating modes
Depending on the operating mode, further accessories are
required:
3.3.1 Requirements for recirculated air mode
yRecirculating air kit DL BUF or DL BUR.
yRecirculated air fan on the fan outlet.
yMinimum size of the fan outlet opening in the lower
cabinet 2 x 250 cm2.
yFilter filling freely accessible for changing.
yThe air escaping from the recirculation filter must be
fed out of the cabinet in a closed system (“guided
recirculating air”).
It is only possible to dispense with a guided recirculating
air system if cabinet or structural building damage due
to moisture (e.g. caused by condensate) can be fully
excluded.
yThe installation variant with recirculated air filter permalyt
(recirculating air kit DL BUR) requires an additional 230 V
socket.
3.3.2 Requirements for extracted air mode
yExhaust air kit DL.
yExhaust air ducting at the fan outlet.
D“3.4 Requirements for the exhaust air ducting
(only for extracted air mode)” (page 12).
yDiameter of the exhaust air ducting at least 150 mm
(corresponds to a surface area of approx. 177 cm2).
yAdequate fresh air supply is assured through the
installation of the necessary accessories.
yWindow contact switch BKA DL.
yWall box.
3.4 Requirements for the exhaust air ducting
(onlyforextracted air mode)
DWARNING!
Fire hazard and asphyxiation hazard due to improper
installation!
When using the exhaust air ducting with other devices
or when connecting an active exhaust air channel (e.g.
chimney), gases or smoke can be drawn into the room.
Make sure that the requirements for the exhaust air
ducting are complied with.
yThe exhaust air ducting is used exclusively by this device.
yThe exhaust air ducting is made of non-combustible
material in accordance with DIN 4102 class B2.
yWhen using a chimney as the exhaust air duct:
yThe chimney must not be used by other devices.
yThe extracted air must be introduced into the
chimney using a 90° bend pointing upwards.
yApproval by a master chimney sweep.
yWhen routing the exhaust air ducting through the roof or
the outside wall:
yThe cross-section must not be smaller than that of the
fan outlet.
yInstallation of condensed water collector in the
exhaust air ducting in order to prevent water damage
inside the device. The condensed water collector must
be adequately dimensioned.
The cross-section, length, type and course of the exhaust
pipe affect the extraction efficiency. Changing the direction
of the air too severely leads to a loss of performance and to
noise.
To optimise the device performance:
yKeep the exhaust air ducting as short as possible (no
longer than 4 m) and route it directly to the outside.
yThe stipulated cross-section of the exhaust air ducting is
complied with.
D“3.3 Requirements for individual operating modes
(page 12).
yExclusive use of ducts and bends with smooth inner
surfaces.
In order to avoid turbulence or backpressure in the
transported air - do not use:
ySpiral hoses.
yFlexible tubes.
yFlat deflection pieces.
ySharp-edged exhaust air channels.
The exhaust air ducting must be in place before installing the
device.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Berbel BKA 83 DLC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Berbel BKA 83 DLC in the language / languages: English as an attachment in your email.

The manual is 13.72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Berbel BKA 83 DLC

Berbel BKA 83 DLC User Manual - German - 40 pages

Berbel BKA 83 DLC User Manual - Dutch - 40 pages

Berbel BKA 83 DLC User Manual - French - 40 pages

Berbel BKA 83 DLC User Manual - Italian - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info