710335

Beper 90313 Manual

11
Zoom out
Zoom in
Previous page
1/32
Next page
ENGLISH
Juice Extractor Use instructions
11
DESCRIPTION OF THE COMPONENTS
1 - Presser
2 - Lid
3 - Centrifugal lter
4- Filter base
5- Locking tabs
6- Juice container
7- Pulp container
8- Motor base
9- ON/OFF switch
10- Non-slip feet
11- Power cord
12- Power cord housing
USE OF THE ELECTRIC HOUSEHOLD APPLIANCE FOR THE FIRST TIME
After you have removed the centrifuge from the wrapping you have to wash all the components,
except for the basis of the motor in warm and soaping water.
ATTENTION: not wash the centrifugal lter in your washing machine because it could demage the
stainless thin retina
Don’t ever bath the basis of the motor in water but clean it with a damp cloth.
DISASSEMBLY AND REASSEMBLY OF THE CENTRIFUGE
Release the locking tabs by pulling the lower part upwards.
Remove the lid. Lift the centrifugal lter and the pulp container.
Remove the juice container and rinse it with running water
To reassemble the components of the centrifuge, place the power cord into its housing, then repo-
sition the pulp container on the motor base and the centrifugal lter in its housing. Ensure that this
has been completely tted in place.
Rest the lid on the Pulp container and hook the locking tabs by pressing them slightly, as shown in
the
gure. Reinsert the juice container in its special seat.
INSTRUCTIONS FOR USE
Run the door of the opening wind-cable to the top and take the feeding cable out of its seat.
Verify that the tension of the device correspond to that of your system (see the technical data em-
bossed plate). Insert the plug of the feeding cable in the current tap. Push the switch to start the
CENTRIFUGE. Even the light lit up.
Pull out the presser. Introduce the food which has been previously cut into small pieces, deprived
of the stones and other tough and brous parts which cannot be centrifuged. Afterwards, slightly
press in the food by means of the presser. Never use your ngers to push the food. Food can be
introduced continually into the ller hole without turning off the motor.
1
2
5
3
11
12
4
9
10
8
6
7
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Beper 90313 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Beper 90313 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 1,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info