711078

Beper 50971 Manual

15
Zoom out
Zoom in
Previous page
1/40
Next page
15
Steam station Use instructions
BEFORE FIRST USE
1. Remove any sticker, protective foil or storage cover from the soleplate.
2. Heat up the iron to maximum temperature and iron over a piece of damp cloth for several minutes
for the purpose of removing any residue on the soleplate according to the section of “Steam ironing”.
3. Before rst use, detach the de-calc box and then immerse it into the water for more than one
minute.
NOTE: It is normal that strange odor comes out from the unit for the rst use. This will cease after
a short while.
NOTE: Some particles may come out of the soleplate when you use the iron for the rst time. This is
normal; the particles are harmless and stop coming out of the iron after a short while.
NOTE: When you switch on the appliance, the steam generator may produce a pumping sound. This
is normal; the sound tells you that water is pumped into the steam generator.
NOTE: During the heating process of the soleplate, there will be little steam coming out from the
soleplate automatically and this phenomenon will continue for about 3 seconds, This is normal.
USING YOUR STEAM STATION IRON
The appliance has two iron portions. You can use dry ironing or steam ironing. The details refer to
the following:
Dry ironing
1. Put the iron on the thermal insulating cushion.
2. Connect the plug to wall outlet, together with one beep can be heard. And then press down the
Power button, the power indicator starts to illuminate.
3. Turn temperature dial to your desired setting, which is depended on the fabric of garment, and the
temperature indicator will illuminate. Refer to IRONING TIPS latter. The iron starts heating.
4. When the temperature indicator turns off, the selected temperature is reached. You now can start
ironing.
WARNING: Never touch hot soleplate at any time before cooling down!
Steam ironing
1. Grasp and press the water tank’s handle to take out of the water tank, then open the lling apertu-
re cap and ll water into the water tank. You had better use puried water with less calcium particles.
After it, close the lling aperture cap. The max capacity of water tank is 1.2L, the water level shall
not be exceeded the MAX mark.
2. Replace the detachable water tank properly.
3. Put the iron on the thermal insulating cushion.
4. Connect the plug to wall outlet, together with one beep can be heard. And then press down the
Power button, the power indicator starts to illuminate, also the low steam level regarded as defaulted
one and its indicator will ash. And you can select other steam level by pressing the steam level
control button according to your requirement. When being selected, its corresponding indicator will
ash.Make sure that there is enough water in the tank.
5. Turn temperature dial to your desired setting, which is depended on the fabric of garment, and
temperature indicator will illuminate. Refer to IRONING TIPS latter.
6. The water in the tank will be heated, after a few minutes, the temperature indicator will be extingui-
shed, which indicates the soleplate temperature has achieved the selected temperature. And when
the indicator of selected steam level has been changed ashing to illuminating, it indicates you can
take out of the iron and iron the garment with steam by pressing the steam trigger of the iron.
Caution: 1) Do not touch hot soleplate at any time before cooling down!
2) Don’t emit the steam directly to the people.
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Beper 50971 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Beper 50971 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 1,95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info