711058

Beper 50161 Manual

12
Zoom out
Zoom in
Previous page
1/52
Next page
12
Cordless iron Use instructions
STEAM IRONING:
While heating, set the steam button to zero «0»
Position the iron in a vertical position and set the temperature control to minimum.
Insert the plug into the wall socket, then turn the temperature control to maximum. The temperature control light
will switch on, indicating that the iron is heating up.
When the light switch off, the set temperature has been reached and the iron is ready for use.
During ironing, the light will turn on and off automatically as the thermostat maintains the set temperature (it is
still possible to continue ironing during this process).
Select the desired amount of steam, using the appropriate button. It is possible to choose between three diffe-
rent types of intensity (zero, one, two), the choice made is visible on the display placed in front of the spray and
steam shot buttons.
The steam is produced as soon as the iron is held in a horizontal position.
CAUTION: Take care not to come into contact with the expelled steam. Do not direct the steam jet to-
wards people and / or animals.
WARNING: If the water in the tank runs out during use, wait until the iron has cooled down before lling
it again.
WARNING: Before using the steam, wait until the temperature has been reached, otherwise the plate may
drip because the steam is not yet ready.
SPRAY
As long as there is enough water in the water tank, you can use the “Spray” button regardless of the set tempe-
rature, and that ironing steam or dry.
When using the iron for the rst time, it is advisable to press the “Spray” button few times before obtaining an
adequate spray, as the water must be able to ll the circulation pipes before exiting.
STEAM SHOT:
The steam shot is used to remove the most stubborn creases.
Set the thermostat knob to the position “●●” or “●●●”.
Set the steam setting button to the maximum position (two)
Press the steam shot button.
NOTE: To avoid water leaking from the plate, do not hold the steam shot button for more than 5 seconds
continuously.
DRY IRONING:
The steam iron can also be used dry with or without water in the water tank. However, it would be better to avoid
lling the water tank while ironing.
Set the steam control button to the minimum position (zero).
Set the temperature control to the most suitable temperature for the fabric to be ironed.
SELF CLEAN (AUTO-CLEANING)
Fill half of the water tank.
Set the temperature control to the maximum position and the steam setting button to the minimum position.
Plug the power cord into the wall socket.
Let the iron warm up until the light switches off.
Holding the iron in a horizontal position above the sink, place the steam selector in the maximum position, press
5 times the “Self Clean” button.
The boiling water, the steam and the impurities will be expelled from the holes in the plate.
Unplug the power cord from the power outlet.
Wait until the iron is cold before storing it.
ANTI-CALC SYSTEM
A special resin lter inside the water tank softens the water and prevents limescale build-up in the plate. The
resin lter is permanent and does not require replacement.
Note:
Do not use chemical additives, scented substances or descaling agents. Failure to comply with the abo-
ve mentioned regulations will make a loss of the warranty.
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Beper 50161 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Beper 50161 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info