710688

Beper 40743 Manual

11
Zoom out
Zoom in
Previous page
1/44
Next page
11
EN
Rechargeable hair clipper Use Instructions
Description of the appliance Fig.A
1. Hair clipper head
2. Cutting length selector
3. ON/OFF switch
4. Display (20/40/60/80/100% charge indicator, charging symbol, lock symbol)
5. Protective cap or beard comb
6. Guiding comb 4-6 mm
7. Guiding comb 7-9 mm
8. Guiding comb 10-12 mm
9. Guiding comb 16-18 mm
10. Guiding comb 22-24 mm
11. Guiding comb 28-30 mm
12. Standing and charging base
13. Power/charging cable
14. Cleaning brush
Use and charge
The appliance can be used either in rechargeable mode as well as connected to the power supply using the
cable supplied. In this way, it is possible to continue using the appliance even if the battery discharges during
use, simply by connecting it to the power outlet.
To use the appliance corded, make sure that the product is switched off before plug in.
To recharge the device, you can:
a. Connect the power cord and recharge the appliance directly, inserting the connector in the appropriate slot at
the base of the hair clipper;
or
b. Connect the power cable to the support base, inserting the connector inside the appropriate slot. Once the
connector is xed, simply place the hair clipper on the base, to start recharging it.
When the appliance is connected to the power supply, the LED charging indicator lights up red on the display,
and remains lit until the battery is fully charged.
During charging the charge level (20/40/60/80/100) will continue to ash until it reaches full charge (100).
Full charging takes about 90 minutes, for a continuous operation of about 90 minutes.
Caution: when recharging the product with the recharging base, take care to place it on a at and stable
surface, away from water and / or heat sources.
Instructions for Use
The product is equipped with 4 different lengths (0.5mm; 1.0mm; 1.5mm; 2.0mm) selectable by using the ap-
propriate button on the side of the product.
The appliance has 6 guiding combs, with different sizes 4-6mm; 7-9mm; 10-12mm; 16-18mm; 22-24mm; 28-
30mm, and a beard comb.
To install the guiding comb and/or beard comb (gure C): position the guide comb on the blade then make sure
that both pins on the sides of the comb match with those on the side of the blade, push lightly until you hear a
slight “click”.
To remove the guiding comb (gure D): grip the guiding comb by the side hooks and pull slightly outwards.
Cut the hair
First, comb the hair thoroughly, removing any knots.
Choose the desired cutting length and the guiding comb according to your needs.
Begin to cut, starting from the neck and proceeding half of the head.
When cutting, let the guiding comb remain attached to the scalp, then move the clipper back and forth.
It is advisable to cut the hair in the opposite direction of hair growth.
Cleaning and maintenance
Before cleaning the appliance, make sure it is switched off and unplugged.
Remove all the accessories, and by using the brush supplied, remove the hair from the blades, for an accurate
cleaning it is also possible to remove the blade, pushing it slightly outwards as shown in gure E.
The head of the hair clipper can be washed with running water, being careful not to let the water penetrate the
body of the product, and drying it carefully immediately afterwards.
Do not immerse the appliance in water. Clean the appliance body with a slightly damp soft cloth.
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Beper 40743 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Beper 40743 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 2,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info