710690

Beper 40742 Manual

9
Zoom out
Zoom in
Previous page
1/44
Next page
9
EN
5 in 1 hair and beard trimmer set Use Instructions
Description of the appliance Fig.A
1. ON/OFF switch
2. Cutting length selector
3. Hair clipper head
4. Shaver head
5. Nose/ear trimmer
6. Hair and beard trimmer
7. Precision trimmer
8. Guiding combs for hair clipper head (3 – 6 – 9 – 12 mm)
9. Guiding comb for hair and beard trimmer head
10. Standing and charging base
11. Adaptor
Charging of the appliance
This appliance can be used with or without the adaptor. It is thus possible to keep using the appliance even when
the battery runs out during operation, by simply plugging it into the wall socket.
In order to do this, make sure that the appliance is turned off before plugging it into the wall socket, and wait
approx. 1 minute before turning the appliance on again.
To charge the appliance:
a. You can connect the adaptor directly to the appliance, by inserting the connection pin in the connector found
at the bottom of hair clipper;
Or
b. You can connect the adaptor to the standing and charging base, by inserting the connection pin inside the
hole found in the hair clipper housing, and blocking it with the cable stopper, to prevent it from detach or falling.
Once the connection pin is xed, simply place the hair clipper on the standing base, to start charging the ap-
pliance.
When the adaptor is plugged into the wall socket, the LED indicator on the display of the hair clipper turns red,
and stays on until the battery is charged.
When the LED indicator turns green, the appliance is fully charged and ready to use.
Complete charging of the appliance takes approximately 90 minutes, for 60 minutes of continuous operation
time.
Instructions for use
The appliance features 5 interchangeable heads, with different functions.
Hair clipper head
This head is used for cutting hair and beard. The 4 guiding combs included in the set allow to cut and trim hair
and beard at 4 different lengths: 3, 6, 9 and 12 mm.
Carefully brush hair and beard before starting to trim them.
Choose the guiding comb for the desired length, and insert it on to the hair clipper head, making sure that it it
well xed before switching on the appliance.
Note: make sure that the appliance is turned off and unplugged from the wall socket before inserting the
guiding comb on to the blade.
For best result, it is better to cut hair and beard following the direction of growth.
For a more precise trimming, you can remove the guiding comb from the hair clipper head, and cut your hair and
beard adjusting the height of the blades using the cutting length selector found on the hair clipper. This selector
allows to adjust blades to 3 different lengths: 0,8 mm – 1,1 mm – 1,4 mm.
Hair and beard trimmer
This head is used for trimming beard and hair. The guiding comb included in the set allows to choose 4 different
trimming lengths: 4, 5, 6 and 7 mm.
Do not leave the appliance unattended if close to places where it
could fall into water (shower, bath tub, sink, etc.). Should the ap-
pliance fall into water, do not try to pick it up; immediately unplug the
adaptor from the wall socket.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Beper 40742 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Beper 40742 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info