710695

Beper 40332 Manual

9
Zoom out
Zoom in
Previous page
1/40
Next page
9
Rechargeable beard trimmer Use instructionsRechargeable beard trimmer Use instructions
EN
Product description Fig.A
1. Cutting length selector
2. ON/OFF switch
3. Charging indicator
4. Comb attachment (1-10mm)
5. Lubricating oil bottle
6. Cleaning brush
Use instructions
Charging of the appliance
Make sure tha the appliance is switched off before charging it.
Insert the power cable in the connector found at the bottom of the appliance, and connect it to a USB plug (USB
wall adapter or PCS USB port). USB wall adapter is not included.
The charging indicator turns on, and it will stay on until the appliance is disconnected from the USB plug.
Normal charging time is 8 hours. Do not charge the appliance for a longer period of time, to avoid damaging the
battery.
8 hours of charging allow up to 60 minutes of continuous use of the appliance.
To ensure maximum life of battery, we recommend the following:
Do not charge the appliance between use sessions; allow the battery to discharge completely.
Discharge completely the batteries at least twice a year (slide the ON/OFF switch to the ON position and let the
appliance run until it stops)
Important! Do not use the appliance while charging
Avoid charging the appliance in direct sunlight or close to direct heat sources.
Use of the appliance
Make sure the appliance is switched off.
Insert the comb attachment as described below, and choose the desired cutting length with the selector.
Note: the cutting length selector does not turn while the appliance is operating.
Slide the ON/OFF switch upwards to turn the appliance on, and proceed with trimming, making sure to move
the appliance against the direction of growth of the hair, and to keep the cutting head as at as possible on the
skin. Clean the comb attachment and the blades after each use, to avoid clogging and consequent damaging
of the appliance.
Mounting/removal of comb attachment
Make sure the appliance is switched off.
To mount the comb attachment, place the cutting length selector on “10”, and x the comb attachment to the
blades as shown in (FIG. B).
To remove the comb attachment, turn the appliance off, place the cutting length selector on “10”, and gently pull
upwards.
Mounting/removal of blades
Make sure the appliance is switched off before proceeding with mounting or removal of blades.
To remove the blades, apply light pressure upwards with your thumb, right on the arrow found at the back of the
appliance (FIG.C).
To mount the blades, align the ribs on each side with the guides found on the appliance, and gently press
downwards until the blades are rmly xed (FIG.C).
Cleaning and maintenance
Make sure that the appliance is switched off, and the power cable unplugged.
Only the blades can be washed under tap water. Do not immerse
the appliance into water, and do not rinse it under tap water.
Do not use abrasive or corrosive detergents to clean the appliance
and the blades.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Beper 40332 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Beper 40332 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info