545231
27
Zoom out
Zoom in
Previous page
1/63
Next page
27
Using the projector
Adjusting the projected image
Adjusting the projection angle
The projector is equipped with 1 quick-release adjuster foot and
1 rear adjuster foot. These adjusters change the image height
and projection angle. To adjust the projector:
1. Press the quick-release button and lift the front of the
projector. Once the image is positioned where you want it,
release the quick-release button to lock the foot in position.
2. Screw the rear adjuster foot to fine-tune the horizontal angle.
To retract the foot, hold up the projector while pressing the quick-release button, then slowly lower the
projector. Screw the rear adjuster foot in a reverse direction.
If the screen and the projector are not perpendicular to each other, the projected image becomes vertical
trapezoidal. To correct this problem, see "Correcting picture distortion" on page 27 for details.
Correcting picture distortion
Keystoning occurs when the projector is not perpendicular to the screen and is where the projected
picture displays visible as a trapezoid shape like either of the following:
Two parallel sides (left and right, or top and bottom) but is noticeably wider on either side.
No parallel sides.
To correct the picture’s shape, you can perform the following steps.
1. Adjust the projection angle. Move the projector to be in front of the center of the screen with the
center of the lens level with the screen.
2. If the picture is stilled distorted, or the projector is unable to be positioned as described above, you
will need to manually correct the picture.
Using the remote control or projector
i. Press one of the Arrow/Keystone keys on the remote control or projector (Up / , Down /
) to display the Keystone page.
ii. See step iii below for further operation.
Using the OSD menu
i. Press MENU/EXIT and then press / until the Display menu is highlighted.
ii. Press to highlight Keystone and press MODE/ENTER. The keystone correction page
displays.
iii. Press the key whose keystone icon is opposite to the shape of the projected picture. Continue
pressing the same key or press the other keys until you are satisfied with the shape.
The values on the lower portion of the page change while pressing. When the values reach their
maximum or minimum with repeated key presses, the picture’s shape will stop changing. You will
not be able to change the picture further in that direction.
2
1
Press
/ .
Press
/ .
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BenQ W770ST at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BenQ W770ST in the language / languages: English as an attachment in your email.

The manual is 4,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of BenQ W770ST

BenQ W770ST User Manual - German - 65 pages

BenQ W770ST User Manual - Dutch - 63 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info