648912
28
Zoom out
Zoom in
Previous page
1/74
Next page
28
Using the projector
English
Correcting picture distortion
Keystoning occurs when the projector is not perpendicular to the screen and is where the projected
picture displays visible as a trapezoid shape like either of the following:
Two parallel sides (left and right, or top and bottom) but is noticeably wider on either side.
No parallel sides.
To correct the picture’s shape, you can perform the following steps.
1. Adjust the projection angle. Move the projector to be in front of the center of the screen with the
center of the lens level with the screen.
2. If the picture is still distorted, or the projector is unable to be positioned as described above, you will
need to manually correct the picture by using the 2D Keystone and Corner Fit functions.
The 2D Keystone function is closely related to the Corner Fit function as both make adjustments to correct
picture distortion. When correcting picture distortion, use the following procedure to adjust 2D Keystone
and Corner Fit functions in order to achieve the best picture shape:
1. Use 2D Keystone function to adjust the picture roughly to the correct shape.
2. Use Corner Fit funtion to fine tune the corners to acheive best picture shape.
3. If optimal effect cannot be achieved using Corner Fit, reset 2D Keystone and repeat steps 1 and 2.
2D Keystone and Corner Fit functions are closely correlated, when 2D Keystone is over adjusted, the
adjustment range for Corner Fit will be limited.
Using 2D Keystone function
Using the remote control or projector keypad
i. Press one of the Arrow/Keystone keys (Left / , Up / ,
Right / , Down / ) to display the 2D Keystone page.
ii. See step iii below for further operation.
Using the OSD menu
i. Press MENU/EXIT and then press / until the Display
menu is highlighted.
ii. Press to highlight 2D Keystone and press MODE/
ENTER. The 2D Keystone page is displayed.
iii. Press the key whose keystone icon is opposite to the shape of the projected picture. Continue
pressing the same key or press the other keys until you are satisfied with the shape.
The values on the lower portion of the page change while pressing. When the values reach their
maximum or minimum with repeated key presses, the picture’s shape will stop changing. You will
not be able to change the picture further in that direction.
iv. If desired picture shape cannot be achieved, press MODE/ENTER to reset 2D Keystone
value and repeat the previous step.
When resetting 2D Keystone, both 2D Keystone and Corner Fit values will return to default value.
v. When done, press MENU/EXIT to go back to the previous page.
Two parallel sides
No parallel sides
Press
/
Press
/
Press
/
Press
/
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BenQ SX930 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BenQ SX930 in the language / languages: English as an attachment in your email.

The manual is 5,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of BenQ SX930

BenQ SX930 User Manual - German - 72 pages

BenQ SX930 User Manual - Dutch - 74 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info