543652
37
Zoom out
Zoom in
Previous page
1/63
Next page
37
Using the projector
English
If one lamp fails, the projector enters Single-Alternative mode automatically. Dual-Brightest, Dual-
Reliable and
Single-Eco settings are not available.
After switching from Dual-Brightest/Dual-Reliable mode to Single-Alternative/Single-Eco mode or vice
versa, wait for 90 seconds before you can adjust the lamp mode again.
A slight variation in the picture brightness and colors may be observed during the very short time of
switching lamp modes.
Controlling the projector through a Lan
environment
Lan Control Settings allow you to manage the projector from a computer using a web browser when the
computer and the projector are properly connected to the same local area network.
Configuring the Lan Control Settings
If you are in a DHCP environment:
1. Take a RJ45 cable and connect one end to the RJ45 LAN input jack of the projector and the other end to
the RJ45 port.
2. Press MENU/EXIT and then press / until the Advanced Setup menu is highlighted.
3. Press to highlight Lan Control Settings and press ENTER. The Lan Control Settings page is
displayed.
4. Press to highlight Control By and press / to select
RJ45.
5. Press to highlight DHCP and press / to select On.
6. Press to highlight AMX Device Discovery and press / to select On or Off. When AMX Device
Discovery is On, the projector can be detected by AMX controller.
7. Press to highlight Apply and press ENTER.
8. Please wait for around 15 - 20 seconds, and then re-enter the Lan Control Settings page.
9. The Projector IP Address, Subnet Mask, Default Gateway, and DNS Server settings will be displayed.
Note down the IP address displayed in the Projector IP Address row.
If the Projector IP Address still does not display, contact your ITS administrator.
If you are in a non-DHCP environment:
1. Repeat steps 1-4 above.
2. Press to highlight DHCP and press / to select Off.
3. Contact your ITS administrator for information on the Projector IP Address,
Subnet Mask, Default
Gateway, and DNS Server settings.
4. Press to select the item you want to modify and press ENTER.
5. Press / to move the cursor and then press / to enter the value.
6. To save the setting, press ENTER. If you do not want to save the setting, press MENU/EXIT.
7. Press to highlight AMX Device Discovery and press / to select On or Off.
8. Press to highlight Apply and press ENTER.
37


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BenQ SH960 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BenQ SH960 in the language / languages: English as an attachment in your email.

The manual is 6,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of BenQ SH960

BenQ SH960 User Manual - Dutch - 63 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info