648906
52
Zoom out
Zoom in
Previous page
1/75
Next page
English
52
Pack the projector in its original packing or equivalent.
Transporting the projector
It is recommended that you ship the projector with its original packing or equivalent.
Replacing the lamp
The projection lamps should be replaced when they burn out. They should only be replaced with a
certied replacement part, contact your local dealer if unsure.
Lamps are positioned differently. Take care not to force the lamps when replacing.
Installation of both lamp modules (Lamp 1 and Lamp 2) is required to operate the projector in dual or single lamp
mode. If only a single lamp module is installed, the projector's lamp will not turn on and will appear as a lamp failure.
The lamp contains a certain amount of mercury and should be disposed of according to local ordinance regulations.
Avoid touching the glass surface of the new lamp: doing so may shorten its operation life.
Lamp Handling Precautions
This projector uses a high-pressure lamp which must be handled carefully and properly. Improper handling may
result in accidents, injury, or create a re hazard.
Lamp life may differ from lamp to lamp and according to the environment of use. There is no guarantee of the same
life for each lamp. Some lamps may fail or terminate their life in a shorter period of time than other similar lamps.
If the projector indicates that the lamp should be replaced, i.e., if LAMP 1 and/or LAMP 2 light up, replace the lamp
with a new one IMMEDIATELY after the projector has cooled down. (Follow carefully the instructions in the Lamp
Replacement section of this manual.) Continuous use of the lamp with LAMP 1 and/or LAMP 2 lighted may increase
the risk of lamp explosion.
A lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its lifetime draws to
an end. Risk of explosion may differ according to the environment or conditions in which the projector and lamp
are being used.
If a lamp explodes, the following safety precautions should be taken:
Disconnect the projector’s AC plug from the AC outlet immediately. Contact an authorized service station for a
checkup of the unit and replacement of the lamp. Additionally, check carefully to ensure that there are no broken
shards or pieces of glass around the projector or coming out from the cooling air circulation holes. Any broken
shards found should be cleaned up carefully. No one should check the inside of the projector except those who
are authorized trained technicians and who are familiar with projector service. Inappropriate attempts to service
the unit by anyone, especially those who are not appropriately trained to do so, may result in an accident or injury
caused by pieces of broken glass.
The projection lamp should be replaced when it burns out. It should only be replaced with a certied replacement
part, which you can order from your local dealer.
Be sure to turn off and unplug the projector at least 30 minutes before replacing the lamp. Failure to do so could
result in a severe burn.
Safety glasses should be worn when replacing the lamp while the projector is ceiling mounted.
52


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BenQ PX9510 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BenQ PX9510 in the language / languages: English as an attachment in your email.

The manual is 27,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of BenQ PX9510

BenQ PX9510 User Manual - German - 79 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info