648906
46
Zoom out
Zoom in
Previous page
1/75
Next page
English
46
Standby Settings
Press
◄►
arrow key to toggle switch between
Standard
,
Eco
and
Network
mode.
Standard
: The projector can be turned on using the remote control, RS-232 command or
network control.
Eco
: The projector maintains in the standby status at the lowest power (<0.5W). In this mode,
the projector can be turned on only using the power button on the remote controller or
projector.
Network
: The projector maintains in the standby status at the power consumption under
6W, the projector can be turned on using the power button or network control only, RS-232
control command and wired remote control signal via external transmitter through RJ45 cable
are not available.
Some of communication ports are turned off if it's set to
Eco
or
Network
mode, please make sure that the Standby
Settings is set to proper setting.
High Altitude
You can use this function to turn the option to
On
for switching the cooling setting if the
project is installed in a high altitude environment, the default is
Off
.
The projector may turn off automatically if it is used in an environment at excessively high
temperature or in an area at a high altitude. In this case, you can enable this function by setting
it to
On
and have the cooling fan operate at a higher speed to low the internal temperature of
the projector.
An area is considered high altitude when it is above 5000 feet.
Auto Power Off
This function enables the projector to enter standby mode automatically when no input signal
is detected more than 15 minutes. Set the function to
On
to enable
Auto Power off
or to
Off
to disable it.
Auto Power On
This function enables the projector to be turned on automatically when the power cord is
plugged into the AC outlet or the breaker switch is turned. Set the function to
On
to enable
this function.
This function is activated by below conditions
The Main Power switch on the projector has to be switched to On.
The projector should be turned off by unplugging power cord or the breaker switch
directly,
Auto Power On
will be activated next time when you plug in the power cord or
turn on breaker switch.
RS232
Baud Rate
: Set transmission speed to:
115200
,
57600
,
38400
,
19200
,
14400
, and
9600
.
Transmission speed shall vary with length of RS-232 cable (longer cable requires slower
speed). In case of unstable signal or connection failure when controlling with RS-232 cable, try
downgrading the transmission speed.
46


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BenQ PX9510 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BenQ PX9510 in the language / languages: English as an attachment in your email.

The manual is 27,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of BenQ PX9510

BenQ PX9510 User Manual - German - 79 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info