214407
19
Zoom out
Zoom in
Previous page
1/36
Next page
19
Using the projector
English
Using the projector
Preparations
1. Plug in and turn all of the connected equipment on.
2. If not already in, plug the supplied power cable into the AC inlet on the
rear of the projector and turn on the power switch.
3. Plug the power cable into a wall socket and turn the wall switch on.
Tur ning the projector on
Follow the steps below.
1. Make sure the Power light is orange after power has been applied and the
main AC power switch is turned on.
2. Press and hold the POWER button on the projector or remote control to turn
the projector on.
The projector will not respond to further commands whilst it is warming up.
3. The fans will be start operating, and a start-up image displays on the screen
for a few seconds whilst it warms up.
4. "Searching…." will be displayed on the screen before the projector identifies
the input signal. This message will remain on the screen until a valid signal is detected.
5. If the horizontal frequency of the input signal exceeds the range of the projector, the message "Unsupported
timing" will be displayed on the screen. This message will remain on-screen until you change the input signal
to an appropriate source.
Selecting an input video source
The projector can be connected to multiple equipment at the same time. To
select an individual input signal, press one of the Source buttons on the remote
control, or to sequentially cycle through all possible sources, press the SOURCE/
ENTER button on the projector.
When the projector is first turned on, it will attempt to reconnect with the
input source which was in use when the projector was last shut down.
If you want to use the PIP or POP function. See page 22 for details.
Adjusting the projected image
Adjusting the projection angle
There are four adjuster feet on the bottom of the projector. These can
be used if necessary to change the projection angle. Screw the feet in or
out as appropriate to aim and level the projection angle.
If the screen and the projector are not perpendicular to each other,
the projected image becomes vertical trapezoidal. To correct this
problem, you can adjust the value of Keystone in the Setup menu.
PE8720-en.book Page 19 Friday, May 13, 2005 5:19 PM
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BenQ pe 8720 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BenQ pe 8720 in the language / languages: English as an attachment in your email.

The manual is 3,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of BenQ pe 8720

BenQ pe 8720 User Manual - Dutch - 38 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info