214255
30
Zoom out
Zoom in
Previous page
1/35
Next page
30 Additional information
Replacing the lamp
(contact your BenQ dealer for assistance)
The lamp mat be very hot. Allow the projector to cool for at least 45 minutes before replacing the lamp.
This lamp contains mercury. Consult your local hazardous waste regulations to dispose of this lamp in a proper
manner.
1. Turn the power off and disconnect the projector from the wall socket.
Turn off all connected equipment and disconnect all other cables.
2. After it has cooled down, turn the projector over. Then loosen the
screws and remove the lamp cover as indicated in the picture.
3. Move the latch to another end as shown in the picture.
4. Loosen the screw that holds the lamp to the projector. If the screw is
not loosened completely, they could injure your fingers. It is strongly
recommended that you use a magnetic-head screwdriver to retain the
screw should it come loose.
5. Lift the handle so that it stands up. Use the handle to slowly pull the
lamp out of the projector.
Pulling it too quickly may cause the lamp to break and scatter broken glass in
the projector. To reduce the risk of injuries to fingers and damage to internal
components, use caution when removing lamp glass that has shattered.
Do not place the lamp in locations where water might splash on it, children can
reach it, near or above heat sources, or near flammable materials.
Do not insert your hands into the projector after the lamp is removed. If you
touch the optical components inside, it could cause color unevenness and distortion of the projected images.
6. Insert a new lamp. Make sure the handle is fully locked, move the
latch back, and tighten the screw firmly.
Loose screw may cause a bad connection, which could result in
malfunction.
Do not over tighten the screw.
7. Re-install the lamp cover and tighten the screw. Do not turn the
power on with the lamp cover removed. Whenever the lamp is
replaced, reset the total lamp operation time. Do not reset if the
lamp is not replaced as this could cause damage.
8. Resetting the lamp counter
i. When the projector is next started, press and hold the Exit 5 button on the
projector for 5 seconds to display the total used lamp time.
ii. Press Auto on the projector or on the remote control to reset the lamp hour to
“0”.
iii. Wait about 5 seconds to let the OSD close.
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BenQ pe 5120 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BenQ pe 5120 in the language / languages: English as an attachment in your email.

The manual is 2,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of BenQ pe 5120

BenQ pe 5120 User Manual - Dutch - 26 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info