542431
19
Zoom out
Zoom in
Previous page
1/77
Next page
Connection 19
Playing sound through the projector
You can make use of the projector (mixed mono) speaker in your presentations, and also
connect separate amplified speakers to the AUDIO OUT socket of the projector.
If you have a separate sound system, you will most likely want to connect the audio output
of your Video source device to that sound system, instead of to the mono audio projector.
You can also use a microphone to output the sound through the projector speaker.
Once connected, the audio can be controlled by the projector On-Screen Display (OSD)
menus. See "Audio Settings" on page 59 for details.
The table below describes the connection methods for different devices, and where the
sound is from.
About the microphone input
If you wish to use a microphone, connect a 3.5 mini jack cable microphone to the
projector.
You can use a wireless microphone as long as a wireless module is attached to the
projector’s microphone input jack and it works well with the associated devices. To
ensure a quality use of the wireless microphone, it is recommended that your
microphone conforms to the specifications listed in the table below.
There are two ways to adjust microphone volumes.
Directly set microphone volume levels in the SYSTEM SETUP: Advanced >
Audio Settings > Microphone Volume menu or press MIC/VOL keys (+/-) on
the remote control.
Set projector volume levels in the SYSTEM SETUP: Advanced > Audio Settings
> Volume menu, or press VOLUME+/VOLUME- on the remote control. (The
projector volume setting will affect the microphone volume.)
To make the microphone input available when the projector is in standby mode, turn on
the SYSTEM SETUP: Advanced > Standby Settings > Microphone menu.
If the microphone is not working, check the volume setting and cable connection.
Device
PC/Component Video Video/S-Video Microphone
Audio input port
AUDIO IN 1 AUDIO IN 2 (L/R)
MIC
The projector can
play the sound
from...
AUDIO IN 1/MIC AUDIO IN 2 (L/R)/MIC
•MIC
AUDIO IN 1/MIC
AUDIO IN 2 (L/R)/
MIC
Audio output port
AUDIO OUT AUDIO OUT AUDIO OUT
The selected input signal determines which sound will be played by the projector speaker,
and which sound will be output from the projector when AUDIO OUT is connected. If you
select a PC signal, the projector can play the sound received from AUDIO IN 1/MIC.
Signal Parameter Min Type Max
Microphone
Transducer Principle Dynamic
Impedance 300 1K ohm
Frequency response 600 16k Hz
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BenQ MX761 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BenQ MX761 in the language / languages: English as an attachment in your email.

The manual is 7,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of BenQ MX761

BenQ MX761 User Manual - Spanish - 80 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info