468671
17
Zoom out
Zoom in
Previous page
1/54
Next page
Bediening 17
Bediening
De projector opstarten
1. Sluit het netsnoer aan op de projector en stop de
stekker in een stopcontact. Schakel het stopcontact
in (indien nodig). Controleer of het POWER
(Power-lampje) op de projector oranje brandt zodra
de stroom is ingeschakeld.
Gebruik uitsluitend de originele accessoires (zoals de
stroomkabel) op het toestel om mogelijke gevaren, zoals
elektrische schok en brand, te voorkomen.
2. Druk op AAN/UIT op de projector of ON op de afstandsbediening om de
projector te starten. Zodra het lampje gaat branden, hoort u een "opstartgeluid".
De POWER (Power-lampje) knippert groen en blijft branden als de projector wordt
ingeschakeld.
Het opstarten duurt ongeveer 30 seconden. In de latere fase van het opstarten wordt
het opstartlogo weergegeven.
Draai zo nodig aan de focusring om de helderheid van het beeld aan te passen.
Zie "Uitschakelen van Beltoon aan/uit" op pagina 32 voor details over het uitschakelen
van de geluidsmelding.
Als de projector nog warm is van de vorige sessie, gaat de ventilator ongeveer 90 seconden
draaien voordat de lamp wordt ingeschakeld.
3. Als de projector voor het eerst wordt geactiveerd,
kies dan uw OSD-taal door de instructies op het
scherm te volgen.
4. Als u om een wachtwoord wordt gevraagd, drukt u
op de pijlknoppen om een wachtwoord van zes
cijfers in te voeren. Zie "De wachtwoordbeveiliging
gebruiken" op pagina 21 voor details.
5. Schakel alle aangesloten apparatuur in.
6. De projector gaat zoeken naar ingangssignalen. Het
momenteel gescande ingangssignaal wordt in de
linkerbovenhoek van het scherm weergegeven. Als
de projector geen goed signaal waarneemt, blijft het
bericht
"Geen signaal" op het scherm staan totdat er een
ingangssignaal wordt gevonden.
U kunt ook op de knop SOURCE op de projector of
afstandsbediening drukken om het gewenste
invoersignaal te selecteren. Zie "Schakelen tussen
ingangssignalen" op pagina 23 voor details.
Als de frequentie/resolutie van het ingangssignaal buiten
het bereik van de projector valt, wordt het bericht 'Buiten
bereik' op een leeg scherm. Selecteer een ingangssignaal
dat compatibel is met de resolutie van de projector of stel
het ingangssignaal op een lager niveau in. Zie "Timing-
diagram" op pagina 52 voor details.
of
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BenQ MS500-V at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BenQ MS500-V in the language / languages: Dutch as an attachment in your email.

The manual is 5,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info