692213

Benning MM 5-2 Manual

20
Zoom out
Zoom in
Previous page
1/134
Next page
10/ 2015
BENNING MM 5-1/ 5-2
21
Note on optional accessory:
- Temperature probe (K-type) made of V4A tube
application: insertion probe for soft-plastic materials, liquids, gas and air
measuring range: - 196 °C up to 800 °C
dimensions: length = 210 mm, tube length = 120 mm, tube diameter =
3 mm, V4A (P.no. 044121)
Note on replaceable parts:
- The BENNING MM 5-2 contains fuses for overload protection:
One fuse rated 15 A rapid-acting (600 V) 50 kA, D = 10.3 mm, L = 38.1 mm
(P.no. 10149447).
- The BENNING MM 5-1/ MM 5-2 is supplied by means of two integrated
1.5 V micro (AAA) batteries (IEC LR 03).
- The above mentioned safety cable (tested spare part) are approved in
accordance with CAT III 1000 V/ CAT IV 600 V and for a current up 10 A.
4. Description of unit
See fig. 1: Front panel
The display and operating elements shown in fig. 1 are as follows:
Digital display, for the measurement reading and display for overrange
indication,
Polarity display,
Battery display,
Function key (blue),
VoltSensor key, for determining AC voltage to earth,
Δ/PEAK key, relative value function and peak value storage
Smart HOLD key,
8
Button (yellow), display illumination,
Rotating switch, for selecting measuring function.
Socket (positive
1
) for V, Ω, , Hz (+) (BENNING MM 5-1) or for V, Ω, ,
Hz, μA, , (BENNING MM 5-2)
COM socket, joint socket for measurement of current, voltage, resistance,
frequency, temperature, capacity, continuity and diode testing,
Socket (positive), for 10-A range, for currents up to 10 A
Protective rubber holster
LED (red) for voltage indicator
1
) The automatic polarity display for DC current and voltage refers to this.
5. General data
5.1 General data on multimeter
5.1.1 The digital display
1
is designed as a 4 digit liquid-crystal indicator with 16
mm digit height and decimal point. The highest value displayed is 6000.
5.1.2 The polarity indication
functions automatically. Only a polarity con-
trary to the socket definition is indicated, as “-”.
5.1.3 The range overload will be displayed with “OL” or “-OL” and sometimes
with an acoustic signal.
Attention: no display or warning by complete overload.
5.1.4 The rotary switch
9
is intended for selecting the measuring function.
The measuring range is selected automatically.
5.1.5 Volt sensor key
5
: The voltage indicator function is intended for local-
izing AC voltages to earth (see 8.9).
5.1.6 Press the Δ/PEAK key
6
(relative value function) to store the currently
displayed value and to display the difference (offset) between the stored
measured value and the following measured values. Press the Δ/PEAK
key
6
for 2 seconds to switch over to the “PEAK” function (peak value
storage). The “PEAK” function detects and stores the positive and
negative peak/ crest value (> 1 ms) in the mV, V AC/ DC and mA, A
AC/ DC function. Press the key to call up Pmax, Pmin and the currently
measured value (Pmax, Pmin). Press the key for approx. 2 seconds to
switch the device back to normal operating mode.
5.1.7 “Smart HOLD” - storage of measurement reading: When the “Smart HOLD”
key is pressed, the measurement reading is stored in the memory.
The symbol “HOLD” appears in the display
1
at the same time. If the
measured value increases by 50 digit above the saved value the change
in measured value is shown by a blinking display and by a signal tone.
(changes of measured values between AC and DC voltage/ current will
not be recognized).
5.1.8 Press the yellow key
8
to activate the display illumination. The device is
switched off automatically after 2 seconds or by pressing the key again.
Deactivate the automatic switch-off by pressing the key (yellow)
8
and
simultaneously switching the BENNING MM 5-2 ON from the switch
position “OFF”.
5.1.9 The function key (blue)
4
serves to select the secondary or third func-
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Benning MM 5-2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Benning MM 5-2 in the language / languages: English, German, Dutch, French, Italian, Polish, Turkish, Spanish as an attachment in your email.

The manual is 5,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info