577325
18
Zoom out
Zoom in
Previous page
1/104
Next page
09/ 2013
BENNING MM 1
11
7.1 Direct voltage ranges
The input impedance is 10 MΩ.
Range Resolution Accuracy
Overload protection
320 mV 100 µV ± (0,5 % of reading + 2 digits) 600 V DC/ AC
3,2 V 1 mV ± (0,5 % of reading + 2 digits) 600 V DC/ AC
32 V 10 mV ± (0,5 % of reading + 2 digits) 600 V DC/ AC
320 V 100 mV ± (0,5 % of reading + 2 digits) 600 V DC/ AC
600 V 1 V ± (0,5 % of reading + 2 digits) 600 V DC/ AC
7.2 Alternating voltage ranges
The input impedance is 10 M parallel 100pF. The measurement value is
arrived at by average sensing and is displayed as the RMS value.
Range
Resolution
Accuracy in 50 Hz - 400 Hz
frequency range
Overload protection
3,2 V 1 mV
± (1,5 % of reading + 5 digits)
in 40 Hz - 300 Hz frequency range for 3 V-range
600 V DC/ AC
32 V 10 mV ± (1,5 % of reading + 5 digits) 600 V DC/ AC
320 V 100 mV ± (1,5 % of reading + 5 digits) 600 V DC/ AC
600 V 1 V ± (1,5 % of reading + 5 digits) 600 V DC/ AC
7.3 Direct current ranges
Range Resolution Accuracy Burden voltage
Overload
protection
320 µA 0,1 µA
± (1,0 % of reading
+ 2 digits) or 3200 µA
< 3 mV/ µA 600 V DC/ AC
3200 µA 1 µA
± (1,0 % of reading
+ 2 digits) or 3200 µA
< 3 mV/ µA 600 V DC/ AC
7.4 Resistance ranges
Overload protection for resistance measurements: 600 V
rms
.
Range Resolution Accuracy Max. open circuit voltage
320 Ω 0,1 ± (1,0 % of reading + 4 digits) 1,3 V
3,2 kΩ 1 Ω ± (0,8 % of reading + 2 digits) 1,3 V
32 kΩ 10 Ω ± (0,8 % of reading + 2 digits) 1,3 V
320 kΩ 100 Ω ± (0,8 % of reading + 2 digits) 1,3 V
3,2 MΩ 1 kΩ ± (0,8 % of reading + 2 digits) 1,3 V
32 MΩ 10 kΩ ± (0,8 % of reading + 5 digits) 1,3 V
7.5 Diode Testing
The accuracy indicated below is valid in the range of 0.4 V to 0.9 V.
Overload protection for diode testing: 600 V
rms
/ 600 V DC.
Range Resolution Accuracy
Maximum
current
Max. open circuit
voltage
1 mV ± (1,5 % of reading + 5 digits) 1,5 mA 3,3 V
7.6 Continuity Testing
The built-in buzzer sounds if the resistance R falls below 20 Ω.
8. Measuring with BENNING MM 1
8.1 Measurement preparation
The BENNING MM 1 must be used and stored only at the indicated storage and
working temperatures, avoid exposure to continuous sunlight.
- Check the rated voltage and current indications on the test leads. The
safety test leads provided with the BENNING MM 1 correspond specifically
to the rated voltage and current of the BENNING MM 1.
- Inspect the test leads for damaged insulation. If the insulation is damaged,
the test leads should be discarded immediately.
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Benning MM 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Benning MM 1 in the language / languages: English, German, Dutch, French, Italian, Polish, Swedish, Turkish, Spanish as an attachment in your email.

The manual is 5,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info