577341

Benning MM 1.2 Manual

22
Zoom out
Zoom in
Previous page
1/169
Next page
13
2. Safetyinstructions
The instrument is built and tested in accordance with
DIN VDE 0411 Teil 1/ EN 61010-1
and has left the factory in perfectly safe technical condition.
To preserve this condition and to ensure safe operation of the device, the user
must observe the notes and warnings given in these instructions at all times.
Thedevicemustbeused inelectrical circuitsof overvoltage
categoryIIwithaconductorforamaximumof1000Vtoearth
orofovervoltagecategoryIIIwithaconductorforamaximum
of600Vtoearthonly.
Onlyusesuitablemeasuringleadsforthis.Withmeasurements
withinmeasurementcategoryIII,theprojectingconductivepart
ofacontacttipofthemeasuringleadsmustnotbelongerthan
4 mm.
Prior to carrying outmeasurementswithinmeasurementca‑
tegoryIII,thepush-oncapsprovidedwiththesetandmarked
with CAT III and CAT IV must be pushed onto the contact tips.
Thepurposeofthismeasureisuserprotection.
Please observe that work on live parts and electrical compon‑
entsofallkindsisdangerous!
Evenlowvoltagesof30VACand60VDCmaybedangerous
tohumanlife.
Beforestartingthecurrentclampmultimeter,alwayscheckthe
deviceaswellasallmeasuringleadsfordamages.
If it can be assumed that safe operation is no longer possible, switch the device
off immediately and secure it against unintended operation.
Safe operation can be assumed to be no longer possible, if
- the device or the measuring leads exhibit visible damages,
- the device no longer works,
- the device has been stored under unfavourable conditions for a longer pe-
riod of time,
- the device was exposed to extraordinary stress during transport.
In order to prevent danger
- donottouchthebaremeasuringprobetipsofthemeasu‑
ring leads,
- insertthemeasuringleadsintotherespectivelydesignated
measuringsocketsofthemultimeter.
3. Scopeofdelivery
The scope of delivery of the BENNING MM 1-1/ 1-2/ 1-3 comprises:
3.1 One BENNING MM 1-1/ 1-2/ 1-3,
3.2 One safety measuring lead, red (L = 1.4 m),
3.3 One safety measuring lead, black (L = 1.4 m),
3.4 One measuring adapter with wire temperature sensor type K
(BENNING MM 1-3)
3.5 One rubber suspension xture,
3.6 One compact protective pouch,
3.7 Two 1.5 V micro (AAA) batteries are integrated into the device,
3.8 One fuse for initial assembly is integrated into the device
(BENNING MM 1-2/ 1-3),
3.9 One operating manual.
Note on optional accessory (BENNING MM 1-3):
- Temperature probe (K-type) made of V4A tube
application: insertion probe for soft-plastic materials, liquids, gas and air
measuring range: - 196 °C up to 800 °C
dimensions: length = 210 mm, tube length = 120 mm, tube diameter =
3 mm, V4A (part no. 044121)
Parts subject to wear:
- The BENNING MM 1-1/ 1-2/ 1-3 is supplied by means of two integrated
1.5 V micro (AAA) batteries (IEC 6 LR 03).
- The BENNING MM 1-2/ 1-3 is equipped with a fuse for overload protection:
One quick-acting fuse, nominal current 10 A (600 V), 50 kA (part no. 748263)
- The safety measuring leads mentioned above (tested accessories) comply
with CAT III 1000 V and are approved for a current of 10 A.
09/ 2013
BENNING MM 1-1/ 1-2/ 1-3
… 22 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Benning MM 1.2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Benning MM 1.2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Turkish, Spanish as an attachment in your email.

The manual is 12,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info